Toshiba B-852-TS12-QP owner manual Product Overview, Introduction Features, Unpacking

Page 8

1. PRODUCT OVERVIEW

ENGLISH VERSION EO1-33028

1.1 Introduction

1. PRODUCT OVERVIEW

1.1 Introduction

Thank you for choosing the TEC B-852 series label/tag printer. This Owner’s Manual contains from general set-up through how to confirm the printer operation using a test print, and should be read carefully to help gain maximum performance and life from your printer. For most queries please refer to this manual and keep it safe for future reference. Please contact your TOSHIBA TEC representative for further information concerning this manual.

1.2 Features

The B-852 printer has the following features:

A 8.3 inch wide print head is installed in such a compact body that the size of the printer body (except the Supply Holder Unit) is about 1/3 of the B-872 printer.

The print head block which can be fully opened realizes great operability.

Various kinds of media can be used since the black mark sensors are located above and under the media passage, respectively, and the media sensors can be moved from the center to the left edge of the media.

When the optional interface board is installed, Web functions such as remote maintenance and other advanced network functions are available.

Superior hardware, including the specially developed 11.8 dots/mm (300 dots/inch) thermal print head which will allow very clear print at a printing speed of 50.8 mm/sec. (2 inches/sec.) or 101.6 mm/sec. (4 inches/sec.).

Besides the optional cutter module, there is also an optional PCMCIA Interface Board, Expansion I/O Interface Board, PCL5 Interface Board Kit, and the KB-80-QM Keyboard Unit.

1.3 Unpacking

NOTES:

Check for damage or scratches on the printer. However, please note that TOSHIBA TEC shall have no liability for any damage of any kind sustained during transportation of the product.

Keep the cartons and pads for future transportation of the printer.

Unpack the printer as per the Unpacking Instructions supplied with the printer.

E1- 1

Image 8
Contents 852-TS12-QP List of Standard of Conformity 852-TS12-QP 6DIHW\6XPPDU\ Precautions Request Regarding MaintenanceTable of Contents E6-1 EA1-1EA2-1 EA3-1Unpacking Introduction FeaturesProduct Overview Accessories Dimensions AppearanceFront View Rear ViewOperation Panel InteriorPrinter Setup PrecautionsProcedure before Operation Assembling the Accessories Assembling the Supply Holder FrameConnecting the Cables to Your Printer Connecting the Power Cord Turning OFF the Printer Turning the PrinterTurning on the Printer Installing the Media onto the Supply Holder Unit Loading the MediaSpacer Supply Holder Printer Loading Media into the Printer Head Pressure Adjust Lever Setting the Feed Gap Sensor Setting the Black Mark SensorLoading the Ribbon Disconnect the mainsInserting the Optional Pcmcia Cards COMTest Print If necessary, the print test may now be repeated from step E2-17 Operating Modes Printer OperationOverview Operating Modes On Line Mode Operation PanelOperation Reset Dump Mode Restart keyPrint Conditions Print Head/Platen/ Sensors MaintenanceCleaning Covers and Panels Optional Cutter ModuleTroubleshooting Error MessagesPossible Problems Possible Problems Causes SolutionsRemoving Jammed Media Threshold Setting Feed keyAppendix 1 Specifications A1.1 PrinterA1.2 Options A1.3 MediaA1.3.1 Media Type LabelA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaA1.4 Ribbon Symbols in the message Appendix 2 Messages and LedsFollowing message appears Appendix 3 Interface „Interface CablesAppendix 4 Print Samples Appendix 4 Print Samples UPC-A Glossaries Bar codePre-printed media Index Index