Ampro Corporation XTX 820 manual Universal Serial Bus USB, Serial Interrupt Request, AC’97 Sound

Page 30

Chapter 3

Hardware

Universal Serial Bus (USB)

The XTX 820 COM supports up to six USB ports on the baseboard and the supported features are listed below.

USB v2.0 backward compatible to legacy v.1.1

Two root hubs and 4 ports on J1

Two ports and 1 root hub on J2

Supports USB boot of floppy disk drives, hard disk drives, CD-ROMs, or other USB boot devices

Integrated physical layer transceivers

Over-current detection status on USB ports 1 and 2

Table 3-5. Simplified USB Interface Pin/Signal Descriptions (J1)

J1

Signal

Description

Pin #

 

 

 

USBP

USB Power –

76

USB0-

Universal Serial Bus Port 0 Data Negative Polarity

 

 

 

88

USB0+

Universal Serial Bus Port 0 Data Positive Polarity

 

 

 

80

USB1-

Universal Serial Bus Port 1 Data Negative Polarity

92

USB1+

Universal Serial Bus Port 1 Data Positive Polarity

 

 

 

58

USB2-

Universal Serial Bus Port 2 Data Negative Polarity

 

 

 

66

USB2+

Universal Serial Bus Port 2 Data Positive Polarity

62

USB3-

Universal Serial Bus Port 3 Data Negative Polarity

 

 

 

72

USB3+

Universal Serial Bus Port 3 Data Positive Polarity

 

 

 

 

GND

USB Port ground

Note: The shaded area denotes power or ground.

Serial Interrupt Request

This SERIRQ signal is connected to serial request input on the I/O Hub (Southbridge) chip (82801FBM) for the alternative LPC/PCI interrupts. If this feature is supported, then DMA2 (DAck2 and DRQ2) shall not be supported by XTX 820 module.

Table 3-6. Simplified Serial Interrupt Request (J1)

J1 Pin #

Signal

Description

21

SERIRQ

Serial Interrupt Request – This pin is used to support the serial interrupt protocol.

 

 

 

AC’97 Sound

The XTX 820 module supports the AC’97 audio standard and the supported features are listed below.

Provides Realtek ALC 655, AC'97/HDA (High Definition Audio CODECs)

AC’97 Rev 2.2 compliant

Supports audio amplifier on baseboard

PC-Beep passthrough to Line Out while reset is held active low

True Line Level Output with volume control independent of Line Out

Digital 3V and 5V compliant

24

Reference Manual

XTX 820

Image 30
Contents XTX Computer On Module Reference Manual Audience Assumptions Contents Index List of Figures List of Tables Reference Manual XTX Specifications Purpose of this ManualReference Material Related Ampro Products XTX 820 Support ProductsAmpro XTX Products Ampro ETX ProductsOther Ampro Products Chapter Chapter Product Overview ETX→ Concept and XTX ExtensionProduct Description Hardware Design PathBoard Features Chapter Chapter Block Diagram COM1 COM2CPU Major Integrated Circuits ICsChip Type Mfg Model Description Function GmhcConnector Definitions Signals DescriptionMechanical Specifications SpecificationsPhysical Specifications DimensionThermal/Cooling Solutions Power SpecificationsEnvironmental Specifications Parameter GHz ULV Celeron GHz LV Pentium M CharacteristicsHardware OverviewCPU U1 MemoryAddress Range Decimal Hex Memory MapAvailable Typical Interrupt Source Connected to Pin SizeAddress hex Size Available Description Address MapAddress Range Size Description Decimal Hex 0CFC 0CFFPCI Bus PCI Bus Interface Connector J1Signal Pin #Devsel GNTPME Frame CBE0 GND AD9 AD6CBE3 CLKREQ CBE2CBE1 Universal Serial Bus USB Signal Description Pin #J1 Pin # Signal Description Serial Interrupt RequestPin # Signal Description VCC1 GNT0VCC0 SerirqVCC3 AoutrVCC2 ReservedVCC4 VCC5PCI Express Interface J2 PCI Express/ExpressCardsSerial ATA Additional Universal Serial Bus USB PortsLPC Interface Extended System ManagementFantachoin PCIGNT#APCIREQ#A FanpwmoutEXC1RST# Fan tachometer input Signal 34-Pin Description Pin # Cable Primary I/O Interface J3Floppy Port Signal DB25 Description Pin # Parallel PortSerial Ports 1 PS/2 Mouse Infrared IrDA PortPS/2 Keyboard CTS2CRT Interface Internal Graphics FeaturesVideo Interface Video EngineLvds Interface J3 Pin # Signal Description TV Out Component and S-Video Comp Floppy Write Protect Senses the diskette is write protected DRV MOTIDE and Auxiliary Interface J4 IDE PortsPiderdy PideiowPideior CblidpLiled Ethernet Port InterfaceTX+ ActledPower Control Signals Power Management SignalsSpeaker Real Time Clock RTC/Battery SMBus I2C BusMatrix Component Address Binary GND4 I2DATGND2 GPE1GND5 GND7VCC6 RXD+ GPE2RXD TXDMiscellaneous Sdvo PortSerial Console Remote Access Temperature MonitoringWatchdog Timer WDT Power-On Switch Power InputPower and Sleep States PwrokSleep States Acpi Signal/Device Condition Wake Up ActivitiesGEP1 Accessing Bios Setup Utility VGA Display IntroductionAccessing Bios Setup Utility Remote Access Bios Setup Utility Menu Item/TopicKey Description Bios MenusBios Main Setup Screen ESCBios Advanced Setup Screen Acpi ConfigurationPCI Configuration PCI IRQ Resource ExclusionAzalia Intel High Definition Audio Graphics Configuration Parallel ATA in Enhanced/Native ModeSerial ATA in Enhanced/Native Mode Flat Panel Resolution BITs AutoCPU Configuration Chipset ConfigurationPCI Express Configuration Interface ConfigurationClock Configuration IDE Configuration Primary IDE Master Not Detected or Device TypeChapter Bios Setup Utility Primary IDE Slave Not Detected or Device Type Secondary IDE Master Not Detected or Device TypeSecondary IDE Slave Not Detected or Device Type Third IDE Master Not Detected or Device TypeThird IDE Slave Not Detected or Device Type Fourth IDE Master Not Detected or Device TypeFourth IDE Slave Not Detected or Device Type USB Configuration Module Version USB Devices Enabled Drives NoneUSB Mass Storage Device Configuration Keyboard/Mouse Configuration Bios PostHardware Health Configuration Watchdog ConfigurationHardware Health Event Monitoring Chapter Bios Setup Utility Bios Boot Setup Screen Boot Priority Selection Device Based or Type BasedBoot Device Priority Boot Settings Configuration Loss Control feature Bios Security Setup Screen To clear Supervisor passwordHard Disk Security Bios Power Setup Screen APMChapter Bios Setup Utility Bios Exit Setup Screen Exit OptionsLoading Defaults Reference Manual XTX Appendix a Technical Support Method Contact InformationAppendix a Appendix B LAN Boot Feature Accessing the LAN PXE Boot Feature Initializing Intel R Boot Agent FE PXE v2.0 Build 0xx WfMAlternate Method of Selecting LAN Boot Press F12 if you want to boot from the NetworkReference Manual XTX Appendix C Connector Part Numbers J6 SdvoAppendix C Acpi PCIUSB CD-ROMRTC Real Time Clock RTC Reference material WDT