Honeywell NETAXS-123 manual Supervised Input Wiring, Supervised Input Terminal Blocks

Page 13

Installing the NetAXS-123 Panels

Panel Components and Descriptions

Figure 3: NetAXS-123 Add-On Board Wiring and Components

2.1 Supervised Input Wiring

The supervised inputs are located on the following terminal blocks:

Table 1: Supervised Input Terminal Blocks

Board Configuration

Terminal Block

 

 

1-Door (Controller Board)

C-TB2

 

C-TB10

 

 

1-Door (Add-On Board)

IO-TB2

 

 

2-Door (Add-On Board)

IO-TB2 (as 1-door Add-On

 

Board)

 

IO-TB6

 

 

NetAXS-123 Access Control Unit Installation Guide, Document 800-05779, Revision A

5

Page 12 Page 14
Image 13
Page 12 Page 14
Contents NetAXS-123 Page Contents RS-485 Connection via PCI-3 RS-485 Connection via NetAXS-123 List of Figures Page List of Tables Page Installing the NetAXS-123 Panels Introduction Access Control Overview NetAXS-123 Overview Panel Components and Descriptions NetAXS-123 Compact Enclosure Wiring and ComponentsNetAXS-123 Standard Enclosure Panel Wiring and Components Board Configuration Terminal Block Supervised Input WiringSupervised Input Terminal Blocks Supervised Tamper Terminal Blocks Typical Supervised Input Wiring DiagramNetAXS-123 Add-On Board NetAXS-123 Access Control UnitNetAXS-123 Input/Output Options Board Readers Inputs/OutputsReaders Supported by NetAXS-123 Supported ReadersSeries Reader Model Honeywell Part Number Real-Time Clock Protection Power SupplySuppressors BatteryInstalling the Compact Enclosure Panel InstallationInstalling on a Wall Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing over a Gang Box Installing on a Flat Surface Installing the Standard Enclosure Panel Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the Add-On Board Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Wiring Readers to the Controller Board Wiring the ReadersFactory Default Configuration Settings for Door IN9 REX IO-TB5 Wiring Door Strikes Or S4 Controller Board DIP Switch and Jumper Settings Setting DIP Switches and JumpersS7 a S8 b S9 b S10 Selection NetAXS-123 SW1 DIP Switch SettingsOFF S1a S2a Selection NetAXS-123 SW2 DIP Switch SettingsExternal NetAXS-123 Controller Board JumpersNormally Open Normally Closed Add-On Board DIP Switch and Jumper Settings12V External Setting the jumpers to configure the relay positionUSB Communications CommunicationsInstalling the NetAXS-123 Panels 2 RS-485 Communications RS-485 Configuration via N-485-PCI-3 RS-485 Configuration via NetAXS-123 Gateway Ethernet TCP/IP Communications Ethernet TCP/IP ConfigurationEthernet Connection System ConfigurationNetAXS-123 USB Connection USB ConnectionRS-485 Connection via PCI-3 RS-485 Connection via PCI-3RS-485 Connection via NetAXS-123 Installing the NetAXS-123 Panels PCI3 56K Dial-up Modem, RS-485 Connection via Hub M-56K Dial-up Modem, RS-485 Connection via Hub PCI-3Fiber Converter to RS-485 Connection via PCI-3 Fiber Converter to RS-485 Connection via PCI-3Fiber Converter to RS-485 Connection via NetAXS-123 Fiber Converter to RS-485 Connection via NetAXS-123Installing the NetAXS-123 Panels Ground only one Mixed Loops PoE Power Limitations Hardware SpecificationsRelay Contacts Reader InterfaceDevice Element Current MechanicalEnvironment Reader WiringCable Card Read / Door Lock Operation Basic Standalone OperationDoor Egress / Door Lock / Door Status Operation Maintenance Troubleshooting Problems and Solutions TroubleshootingProblem Solution Normal Support Hours Technical SupportWeb This page is left blank for printing purposes Honeywell Access Systems
Top Page Image Contents