Honeywell Reset Admin Password, Find Default IP and Password, and Configure DIP Switch Settings for NetAXS-123

Page 46

Installing the NetAXS-123 Panels

Installation

b.Both DIP Switch 8 and DIP Switch 9 need to be either ON or OFF to be properly configured.

Table 9: NetAXS-123 SW2 DIP Switch Settings

S1a

S2a

Selection

OFF	OFF	RS-485_2 termination (EOL) DISABLED

ON	ON	RS-485_2 termination (EOL) ENABLED (FUTURE) (Default)

a.Both DIP Switch 1 and DIP Switch 2 need to be either ON or OFF to be properly configured.

Note: When you use the DIP switches to reset a panel to the original factory default values, the Event History is lost and any customized databases are removed, so the panel is reset with the original factory default database. This does not affect the Ethernet IP address.

You can also use this ASCII command:

_I=pn_R

This command resets the panel to the original factory default values, but it only removes the customized databases and restores the original factory default database. The Event History is retained.

To reset the panel to the factory default values:

1.Make a note of the existing settings on SW1 DIP switches.

2.While the panel is powered up, turn all DIP switches to the OFF position.

3.Power down, then power the panel back up.

4.Wait for the panel to come up. The RUN LED should flicker fast.

5.Set the DIP switches back to their original positions.

6.Power down, then power the panel back up.

7.After the the panel comes up, the RUN LED should flash normal.

The panel is now reset to the original factory default values.

Note: Address 0 is not a valid setting.

38www.honeywell.com

Image 46

Contents NetAXS-123 Page Contents RS-485 Connection via PCI-3 RS-485 Connection via NetAXS-123 List of Figures Page List of Tables Page Installing the NetAXS-123 Panels Introduction Access Control OverviewNetAXS-123 Overview NetAXS-123 Compact Enclosure Wiring and Components Panel Components and DescriptionsNetAXS-123 Standard Enclosure Panel Wiring and Components Board Configuration Terminal Block Supervised Input WiringSupervised Input Terminal Blocks Typical Supervised Input Wiring Diagram Supervised Tamper Terminal BlocksNetAXS-123 Input/Output Options NetAXS-123 Access Control UnitNetAXS-123 Add-On Board Board Readers Inputs/OutputsReaders Supported by NetAXS-123 Supported ReadersSeries Reader Model Honeywell Part Number Power Supply Real-Time Clock ProtectionBattery SuppressorsInstalling the Compact Enclosure Panel InstallationInstalling on a Wall Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing over a Gang Box Installing on a Flat Surface Installing the Standard Enclosure Panel Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the Add-On Board Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Wiring the Readers Wiring Readers to the Controller BoardFactory Default Configuration Settings for Door IN9 REX IO-TB5 Wiring Door Strikes Or S4 Setting DIP Switches and Jumpers Controller Board DIP Switch and Jumper SettingsNetAXS-123 SW1 DIP Switch Settings S7 a S8 b S9 b S10 SelectionOFF NetAXS-123 SW2 DIP Switch Settings S1a S2a SelectionNetAXS-123 Controller Board Jumpers ExternalAdd-On Board DIP Switch and Jumper Settings Normally Open Normally ClosedSetting the jumpers to configure the relay position 12V ExternalCommunications USB CommunicationsInstalling the NetAXS-123 Panels 2 RS-485 Communications RS-485 Configuration via N-485-PCI-3 RS-485 Configuration via NetAXS-123 Gateway Ethernet TCP/IP Configuration Ethernet TCP/IP CommunicationsSystem Configuration Ethernet ConnectionUSB Connection NetAXS-123 USB ConnectionRS-485 Connection via PCI-3 RS-485 Connection via PCI-3RS-485 Connection via NetAXS-123 Installing the NetAXS-123 Panels PCI3 M-56K Dial-up Modem, RS-485 Connection via Hub PCI-3 56K Dial-up Modem, RS-485 Connection via HubFiber Converter to RS-485 Connection via PCI-3 Fiber Converter to RS-485 Connection via PCI-3Fiber Converter to RS-485 Connection via NetAXS-123 Fiber Converter to RS-485 Connection via NetAXS-123Installing the NetAXS-123 Panels Ground only one Mixed Loops Relay Contacts Hardware SpecificationsPoE Power Limitations Reader InterfaceMechanical Device Element CurrentEnvironment Reader WiringCable Card Read / Door Lock Operation Basic Standalone OperationDoor Egress / Door Lock / Door Status Operation Maintenance Troubleshooting Problems and Solutions TroubleshootingProblem Solution Normal Support Hours Technical SupportWeb This page is left blank for printing purposes Honeywell Access Systems