Honeywell NETAXS-123 manual System Configuration, Ethernet Connection

Page 56

Installing the NetAXS-123 Panels

System Configuration

4.0 System Configuration

This section provides wiring diagrams for each of the NetAXS-123 system configurations.

4.1 Ethernet Connection

Figure 12: Ethernet Connection

NIC	100BaseT (CAT 5) 328 Ft. Max.

NetAXS-123

Panel

EG	EG	EG	EG
	DIP Switch Settings		DIP Switch Settings
	S1-S5 Panel Address		S1-S5 Panel Address
	S6: OFF		S6: OFF
	S7: OFF		S7: OFF
	S8-S9: ON: 485 Termination ON		S8-S9: ON: 485 Termination ON

Note: You should ground each NetAXS-123 Standard (Metal) Enclosure panel individually with an Earth Ground.

48www.honeywell.com

Image 56

Contents NetAXS-123 Page Contents RS-485 Connection via PCI-3 RS-485 Connection via NetAXS-123 List of Figures Page List of Tables Page Installing the NetAXS-123 Panels NetAXS-123 Overview Access Control OverviewIntroduction NetAXS-123 Compact Enclosure Wiring and Components Panel Components and DescriptionsNetAXS-123 Standard Enclosure Panel Wiring and Components Supervised Input Terminal Blocks Supervised Input WiringBoard Configuration Terminal Block Typical Supervised Input Wiring Diagram Supervised Tamper Terminal BlocksNetAXS-123 Access Control Unit NetAXS-123 Add-On BoardNetAXS-123 Input/Output Options Board Readers Inputs/OutputsSeries Reader Model Honeywell Part Number Supported ReadersReaders Supported by NetAXS-123 Power Supply Real-Time Clock ProtectionBattery SuppressorsInstalling on a Wall InstallationInstalling the Compact Enclosure Panel Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing over a Gang Box Installing on a Flat Surface Installing the Standard Enclosure Panel Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the Add-On Board Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Wiring the Readers Wiring Readers to the Controller BoardFactory Default Configuration Settings for Door IN9 REX IO-TB5 Wiring Door Strikes Or S4 Setting DIP Switches and Jumpers Controller Board DIP Switch and Jumper SettingsNetAXS-123 SW1 DIP Switch Settings S7 a S8 b S9 b S10 SelectionOFF NetAXS-123 SW2 DIP Switch Settings S1a S2a SelectionNetAXS-123 Controller Board Jumpers ExternalAdd-On Board DIP Switch and Jumper Settings Normally Open Normally ClosedSetting the jumpers to configure the relay position 12V ExternalCommunications USB CommunicationsInstalling the NetAXS-123 Panels 2 RS-485 Communications RS-485 Configuration via N-485-PCI-3 RS-485 Configuration via NetAXS-123 Gateway Ethernet TCP/IP Configuration Ethernet TCP/IP CommunicationsSystem Configuration Ethernet ConnectionUSB Connection NetAXS-123 USB ConnectionRS-485 Connection via PCI-3 RS-485 Connection via PCI-3RS-485 Connection via NetAXS-123 Installing the NetAXS-123 Panels PCI3 M-56K Dial-up Modem, RS-485 Connection via Hub PCI-3 56K Dial-up Modem, RS-485 Connection via HubFiber Converter to RS-485 Connection via PCI-3 Fiber Converter to RS-485 Connection via PCI-3Fiber Converter to RS-485 Connection via NetAXS-123 Fiber Converter to RS-485 Connection via NetAXS-123Installing the NetAXS-123 Panels Ground only one Mixed Loops Hardware Specifications PoE Power LimitationsRelay Contacts Reader InterfaceMechanical Device Element CurrentCable Reader WiringEnvironment Door Egress / Door Lock / Door Status Operation Basic Standalone OperationCard Read / Door Lock Operation Maintenance Problem Solution TroubleshootingTroubleshooting Problems and Solutions Web Technical SupportNormal Support Hours This page is left blank for printing purposes Honeywell Access Systems