Honeywell NETAXS-123 manual NetAXS-123 Standard Enclosure Panel Wiring and Components

Page 12

Installing the NetAXS-123 Panels

Panel Components and Descriptions

Figure 2: NetAXS-123 Standard Enclosure Panel Wiring and Components

Note: Maintain at least a .25-inch distance between the non-power limited wiring (115 VAC/60 Hz input wiring, power line filter wiring, and battery backup/charger wiring) and all other wiring, which is power-limited Class 2 wiring.

4www.honeywell.com

Image 12

Contents NetAXS-123 Page Contents RS-485 Connection via PCI-3 RS-485 Connection via NetAXS-123 List of Figures Page List of Tables Page Installing the NetAXS-123 Panels Access Control Overview IntroductionNetAXS-123 Overview NetAXS-123 Compact Enclosure Wiring and Components Panel Components and DescriptionsNetAXS-123 Standard Enclosure Panel Wiring and Components Supervised Input Wiring Board Configuration Terminal BlockSupervised Input Terminal Blocks Typical Supervised Input Wiring Diagram Supervised Tamper Terminal BlocksNetAXS-123 Access Control Unit NetAXS-123 Add-On BoardNetAXS-123 Input/Output Options Board Readers Inputs/OutputsSupported Readers Readers Supported by NetAXS-123Series Reader Model Honeywell Part Number Power Supply Real-Time Clock ProtectionBattery SuppressorsInstallation Installing the Compact Enclosure PanelInstalling on a Wall Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing over a Gang Box Installing on a Flat Surface Installing the Standard Enclosure Panel Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the Add-On Board Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Wiring the Readers Wiring Readers to the Controller BoardFactory Default Configuration Settings for Door IN9 REX IO-TB5 Wiring Door Strikes Or S4 Setting DIP Switches and Jumpers Controller Board DIP Switch and Jumper SettingsNetAXS-123 SW1 DIP Switch Settings S7 a S8 b S9 b S10 SelectionOFF NetAXS-123 SW2 DIP Switch Settings S1a S2a SelectionNetAXS-123 Controller Board Jumpers ExternalAdd-On Board DIP Switch and Jumper Settings Normally Open Normally ClosedSetting the jumpers to configure the relay position 12V ExternalCommunications USB CommunicationsInstalling the NetAXS-123 Panels 2 RS-485 Communications RS-485 Configuration via N-485-PCI-3 RS-485 Configuration via NetAXS-123 Gateway Ethernet TCP/IP Configuration Ethernet TCP/IP CommunicationsSystem Configuration Ethernet ConnectionUSB Connection NetAXS-123 USB ConnectionRS-485 Connection via PCI-3 RS-485 Connection via PCI-3RS-485 Connection via NetAXS-123 Installing the NetAXS-123 Panels PCI3 M-56K Dial-up Modem, RS-485 Connection via Hub PCI-3 56K Dial-up Modem, RS-485 Connection via HubFiber Converter to RS-485 Connection via PCI-3 Fiber Converter to RS-485 Connection via PCI-3Fiber Converter to RS-485 Connection via NetAXS-123 Fiber Converter to RS-485 Connection via NetAXS-123Installing the NetAXS-123 Panels Ground only one Mixed Loops Hardware Specifications PoE Power LimitationsRelay Contacts Reader InterfaceMechanical Device Element CurrentReader Wiring EnvironmentCable Basic Standalone Operation Card Read / Door Lock OperationDoor Egress / Door Lock / Door Status Operation Maintenance Troubleshooting Troubleshooting Problems and SolutionsProblem Solution Technical Support Normal Support HoursWeb This page is left blank for printing purposes Honeywell Access Systems