Honeywell NETAXS-123 manual Installing the Standard Enclosure Panel

Page 25

Installing the NetAXS-123 Panels

Installation

3.2 Installing the Standard Enclosure Panel

Perform the following steps to install the NetAXS-123 Standard Enclosure panel:

Warning: Use a static strap whenever touching the panel to ensure protection from Electrostatic Discharge (ESD).

1. (Optional) Remove the green ground wire and the door.

2. Partially install the four power supply screws.

NetAXS-123 Access Control Unit Installation Guide, Document 800-05779, Revision A

17

Image 25

Contents NetAXS-123 Page Contents RS-485 Connection via PCI-3 RS-485 Connection via NetAXS-123 List of Figures Page List of Tables Page Installing the NetAXS-123 Panels Introduction Access Control OverviewNetAXS-123 Overview Panel Components and Descriptions NetAXS-123 Compact Enclosure Wiring and ComponentsNetAXS-123 Standard Enclosure Panel Wiring and Components Board Configuration Terminal Block Supervised Input WiringSupervised Input Terminal Blocks Supervised Tamper Terminal Blocks Typical Supervised Input Wiring DiagramNetAXS-123 Add-On Board NetAXS-123 Access Control UnitNetAXS-123 Input/Output Options Board Readers Inputs/OutputsReaders Supported by NetAXS-123 Supported ReadersSeries Reader Model Honeywell Part Number Real-Time Clock Protection Power SupplySuppressors BatteryInstalling the Compact Enclosure Panel InstallationInstalling on a Wall Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing over a Gang Box Installing on a Flat Surface Installing the Standard Enclosure Panel Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the Add-On Board Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Wiring Readers to the Controller Board Wiring the ReadersFactory Default Configuration Settings for Door IN9 REX IO-TB5 Wiring Door Strikes Or S4 Controller Board DIP Switch and Jumper Settings Setting DIP Switches and JumpersS7 a S8 b S9 b S10 Selection NetAXS-123 SW1 DIP Switch SettingsOFF S1a S2a Selection NetAXS-123 SW2 DIP Switch SettingsExternal NetAXS-123 Controller Board JumpersNormally Open Normally Closed Add-On Board DIP Switch and Jumper Settings12V External Setting the jumpers to configure the relay positionUSB Communications CommunicationsInstalling the NetAXS-123 Panels 2 RS-485 Communications RS-485 Configuration via N-485-PCI-3 RS-485 Configuration via NetAXS-123 Gateway Ethernet TCP/IP Communications Ethernet TCP/IP ConfigurationEthernet Connection System ConfigurationNetAXS-123 USB Connection USB ConnectionRS-485 Connection via PCI-3 RS-485 Connection via PCI-3RS-485 Connection via NetAXS-123 Installing the NetAXS-123 Panels PCI3 56K Dial-up Modem, RS-485 Connection via Hub M-56K Dial-up Modem, RS-485 Connection via Hub PCI-3Fiber Converter to RS-485 Connection via PCI-3 Fiber Converter to RS-485 Connection via PCI-3Fiber Converter to RS-485 Connection via NetAXS-123 Fiber Converter to RS-485 Connection via NetAXS-123Installing the NetAXS-123 Panels Ground only one Mixed Loops PoE Power Limitations Hardware SpecificationsRelay Contacts Reader InterfaceDevice Element Current MechanicalEnvironment Reader WiringCable Card Read / Door Lock Operation Basic Standalone OperationDoor Egress / Door Lock / Door Status Operation Maintenance Troubleshooting Problems and Solutions TroubleshootingProblem Solution Normal Support Hours Technical SupportWeb This page is left blank for printing purposes Honeywell Access Systems