Honeywell NETAXS-123 Supervised Tamper Terminal Blocks, Typical Supervised Input Wiring Diagram

Page 14

Installing the NetAXS-123 Panels

Panel Components and Descriptions

Tampers can also be supervised. They are located on the following terminal blocks:

Table 2: Supervised Tamper Terminal Blocks

Board Configuration

Terminal Block

 

 

1-Door (Controller Board)

C-TB3/TMPR A

 

C-TB4/TMPR B

 

 

1-Door (Add-On Board)

IO-TB3/TMPR A

 

IO-TB4/TMPR B

 

 

2-Door (Add-On Board)

IO-TB3/TMPR A

 

IO-TB4/TMPR B

 

IO-TB7/TMPR A

 

IO-TB8/TMPR B

 

 

Door Status (STS) and Request to Exit (REX) for all three doors may be configured for Normally Open or Normally Closed contacts as supervised or non-supervised. Inputs 5 (generic) and 6 (power) are on C-TB10. All seven inputs on the Controller Board and four inputs on the Add-On Board have default functions, but they can be configured for general purpose inputs.

The following figure shows the typical wiring for a supervised input.

Figure 4: Typical Supervised Input Wiring Diagram

The figure above shows standard 2,200 ohm resistors. The NetAXS-123 panel accepts 1,000, 2,200, 4,700, or 10,000 ohm values. Note that both resistors must have the same value.

In addition, the Reader tampers can be supervised and capable of being used as additional inputs if the default functionality is not needed.

The wire used for the inputs should be shielded and cannot exceed 30 ohms over the entire length of the cable. Remember that the distance from the panel to the door must be doubled to determine the total resistance.

Caution: The cable shield should be grounded only at the panel earth ground. Grounding at both ends can cause ground loops which can be disruptive.

6www.honeywell.com

Page 13 Page 15
Image 14
Page 13 Page 15
Contents NetAXS-123 Page Contents RS-485 Connection via PCI-3 RS-485 Connection via NetAXS-123 List of Figures Page List of Tables Page Installing the NetAXS-123 Panels NetAXS-123 Overview Access Control OverviewIntroduction NetAXS-123 Compact Enclosure Wiring and Components Panel Components and DescriptionsNetAXS-123 Standard Enclosure Panel Wiring and Components Supervised Input Terminal Blocks Supervised Input WiringBoard Configuration Terminal Block Typical Supervised Input Wiring Diagram Supervised Tamper Terminal BlocksNetAXS-123 Input/Output Options NetAXS-123 Access Control UnitNetAXS-123 Add-On Board Board Readers Inputs/OutputsSeries Reader Model Honeywell Part Number Supported ReadersReaders Supported by NetAXS-123 Power Supply Real-Time Clock ProtectionBattery SuppressorsInstalling on a Wall InstallationInstalling the Compact Enclosure Panel Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing over a Gang Box Installing on a Flat Surface Installing the Standard Enclosure Panel Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the Add-On Board Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Wiring the Readers Wiring Readers to the Controller BoardFactory Default Configuration Settings for Door IN9 REX IO-TB5 Wiring Door Strikes Or S4 Setting DIP Switches and Jumpers Controller Board DIP Switch and Jumper SettingsNetAXS-123 SW1 DIP Switch Settings S7 a S8 b S9 b S10 SelectionOFF NetAXS-123 SW2 DIP Switch Settings S1a S2a SelectionNetAXS-123 Controller Board Jumpers ExternalAdd-On Board DIP Switch and Jumper Settings Normally Open Normally ClosedSetting the jumpers to configure the relay position 12V ExternalCommunications USB CommunicationsInstalling the NetAXS-123 Panels 2 RS-485 Communications RS-485 Configuration via N-485-PCI-3 RS-485 Configuration via NetAXS-123 Gateway Ethernet TCP/IP Configuration Ethernet TCP/IP CommunicationsSystem Configuration Ethernet ConnectionUSB Connection NetAXS-123 USB ConnectionRS-485 Connection via PCI-3 RS-485 Connection via PCI-3RS-485 Connection via NetAXS-123 Installing the NetAXS-123 Panels PCI3 M-56K Dial-up Modem, RS-485 Connection via Hub PCI-3 56K Dial-up Modem, RS-485 Connection via HubFiber Converter to RS-485 Connection via PCI-3 Fiber Converter to RS-485 Connection via PCI-3Fiber Converter to RS-485 Connection via NetAXS-123 Fiber Converter to RS-485 Connection via NetAXS-123Installing the NetAXS-123 Panels Ground only one Mixed Loops Relay Contacts Hardware SpecificationsPoE Power Limitations Reader InterfaceMechanical Device Element CurrentCable Reader WiringEnvironment Door Egress / Door Lock / Door Status Operation Basic Standalone OperationCard Read / Door Lock Operation Maintenance Problem Solution TroubleshootingTroubleshooting Problems and Solutions Web Technical SupportNormal Support Hours This page is left blank for printing purposes Honeywell Access Systems

NETAXS-123 specifications

The Honeywell NETAXS-123 is an advanced access control solution designed to enhance security and efficiency for various facilities, including commercial buildings, educational institutions, and healthcare facilities. It provides a versatile platform that integrates cutting-edge technologies to simplify access management while maintaining a high level of protection.

One of the standout features of the NETAXS-123 is its web-based interface, which allows administrators to manage access from anywhere with an internet connection. This cloud-based accessibility is a significant advantage for organizations that require real-time monitoring and control over their security systems. Users can easily configure access rights, generate reports, and monitor system events through a user-friendly dashboard that minimizes the need for extensive training.

The NETAXS-123 supports a range of authentication methods, including key cards, biometric readers, and mobile credentials, ensuring that organizations can implement the best solution for their specific security needs. The system facilitates multiple entry points, enabling different access levels for various personnel, which helps in maintaining strict control over sensitive areas.

Another feature is its scalability. The NETAXS-123 can accommodate small installations with just a few doors and is easily expandable to support larger operations with dozens of access points. This flexibility makes it ideal for growing organizations that anticipate changes in their access control needs.

The system is equipped with advanced reporting capabilities, allowing administrators to generate detailed activity logs and audit trails. These logs play a crucial role in investigating incidents and ensuring compliance with industry regulations and standards, making the NETAXS-123 a reliable choice for organizations focused on security and accountability.

In terms of connectivity, the NETAXS-123 integrates seamlessly with existing IT infrastructures, supporting Ethernet and Wi-Fi connectivity options. This compatibility ensures smooth operation and easy integration with other security systems like CCTV and alarm monitoring.

The hardware components of the NETAXS-123 are built with durable materials, ensuring longevity and reliable performance, even in demanding environments. With features such as power over Ethernet (PoE), the system simplifies installation by reducing the need for separate power sources, allowing for more streamlined deployments.

In conclusion, the Honeywell NETAXS-123 combines advanced features, user-friendly technology, and robust security measures to deliver an effective access control solution. Its scalability, diverse authentication methods, and real-time management capabilities make it a top choice for organizations looking to enhance their security infrastructure.
Top Page Image Contents