Honeywell NETAXS-123 manual Mixed Loops

Page 67

Installing the NetAXS-123 Panels

System Configuration

4.11 Mixed Loops

This mixed-loop configuration supports a combined total of 31 N1000 III, N1000 IV, NetAXS, NetAXS-123, and NS2 panels per Multidrop line.

NetAXS-123 Access Control Unit Installation Guide, Document 800-05779, Revision A

59

Image 67

Contents NetAXS-123 Page Contents RS-485 Connection via PCI-3 RS-485 Connection via NetAXS-123 List of Figures Page List of Tables Page Installing the NetAXS-123 Panels Introduction Access Control OverviewNetAXS-123 Overview Panel Components and Descriptions NetAXS-123 Compact Enclosure Wiring and ComponentsNetAXS-123 Standard Enclosure Panel Wiring and Components Board Configuration Terminal Block Supervised Input WiringSupervised Input Terminal Blocks Supervised Tamper Terminal Blocks Typical Supervised Input Wiring DiagramBoard Readers Inputs/Outputs NetAXS-123 Access Control UnitNetAXS-123 Add-On Board NetAXS-123 Input/Output OptionsReaders Supported by NetAXS-123 Supported ReadersSeries Reader Model Honeywell Part Number Real-Time Clock Protection Power SupplySuppressors BatteryInstalling the Compact Enclosure Panel InstallationInstalling on a Wall Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing over a Gang Box Installing on a Flat Surface Installing the Standard Enclosure Panel Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the Add-On Board Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Wiring Readers to the Controller Board Wiring the ReadersFactory Default Configuration Settings for Door IN9 REX IO-TB5 Wiring Door Strikes Or S4 Controller Board DIP Switch and Jumper Settings Setting DIP Switches and JumpersS7 a S8 b S9 b S10 Selection NetAXS-123 SW1 DIP Switch SettingsOFF S1a S2a Selection NetAXS-123 SW2 DIP Switch SettingsExternal NetAXS-123 Controller Board JumpersNormally Open Normally Closed Add-On Board DIP Switch and Jumper Settings12V External Setting the jumpers to configure the relay positionUSB Communications CommunicationsInstalling the NetAXS-123 Panels 2 RS-485 Communications RS-485 Configuration via N-485-PCI-3 RS-485 Configuration via NetAXS-123 Gateway Ethernet TCP/IP Communications Ethernet TCP/IP ConfigurationEthernet Connection System ConfigurationNetAXS-123 USB Connection USB ConnectionRS-485 Connection via PCI-3 RS-485 Connection via PCI-3RS-485 Connection via NetAXS-123 Installing the NetAXS-123 Panels PCI3 56K Dial-up Modem, RS-485 Connection via Hub M-56K Dial-up Modem, RS-485 Connection via Hub PCI-3Fiber Converter to RS-485 Connection via PCI-3 Fiber Converter to RS-485 Connection via PCI-3 Fiber Converter to RS-485 Connection via NetAXS-123 Fiber Converter to RS-485 Connection via NetAXS-123Installing the NetAXS-123 Panels Ground only one Mixed Loops Reader Interface Hardware SpecificationsPoE Power Limitations Relay ContactsDevice Element Current MechanicalEnvironment Reader WiringCable Card Read / Door Lock Operation Basic Standalone OperationDoor Egress / Door Lock / Door Status Operation Maintenance Troubleshooting Problems and Solutions TroubleshootingProblem Solution Normal Support Hours Technical SupportWeb This page is left blank for printing purposes Honeywell Access Systems