Honeywell NETAXS-123 manual Hardware Specifications, Relay Contacts, Reader Interface

Page 68

Installing the NetAXS-123 Panels

Hardware Specifications

5.0 Hardware Specifications

The specifications in this section apply to both the Standard Enclosure and Compact Enclosure panels.

5.1 Relay Contacts

Maximum of six Form-C SPDT relays, 3A (at dry contact) or 0.5A (at self-whetted) @ 30VDC (PTC limited in the self-whetted mode). The Form-C SPDT relays are configured as Normally Open or Normally Closed outputs only. Normally Open and Normally Closed contacts cannot be used simultaneously.

5.2Reader Interface

•Reader Power: 12VDC nominal with 500mA maximum for each reader port.

•Reader LED Output: Open collector driver capable of sinking up to 8mA.

•Reader Tamper: Supervised or non-supervised input.

•Reader Data Input: TTL compatible inputs.

5.3Maximum Output Loading

Use the following guidelines unless you are using Power Over Ethernet (PoE):

•Maximum current per reader port for any of the three reader outputs is 500mA.

•Maximum current for any of the six relay outputs on the Songchuan 892N-1CH-1F-V is 3A at dry contact, or 0.5A at self-whetted.

•Maximum battery charge current for the battery wired in series is 250mA.

•External power on C-TB9 is limited to 1.5A @ 12VDC.

5.4PoE Power Limitations

If you are using the NetAXS-123 Standard Enclosure and powering the panel with PoE (Power over Ethernet), you must comply with these specifications for proper operation:

•A NetAXS-123 panel powered by PoE is 802.3af compliant, providing a maximum of 15.4W of input power to the panel. This input power is split between on-board power consumption and external load consumption. A maximum current capacity of 450 mA @ 12VDC is available for all external devices combined.

Notes:

• Two readers per door can still be supported as long as the total current is within the external load capacity stated above.

•You can either find the devices’ power consumption amounts by referring to the products’ documentation or by using a current meter.

60www.honeywell.com

Image 68

Contents NetAXS-123 Page Contents RS-485 Connection via PCI-3 RS-485 Connection via NetAXS-123 List of Figures Page List of Tables Page Installing the NetAXS-123 Panels NetAXS-123 Overview Access Control OverviewIntroduction NetAXS-123 Compact Enclosure Wiring and Components Panel Components and DescriptionsNetAXS-123 Standard Enclosure Panel Wiring and Components Supervised Input Terminal Blocks Supervised Input WiringBoard Configuration Terminal Block Typical Supervised Input Wiring Diagram Supervised Tamper Terminal BlocksNetAXS-123 Access Control Unit NetAXS-123 Add-On BoardNetAXS-123 Input/Output Options Board Readers Inputs/OutputsSeries Reader Model Honeywell Part Number Supported ReadersReaders Supported by NetAXS-123 Power Supply Real-Time Clock ProtectionBattery SuppressorsInstalling on a Wall InstallationInstalling the Compact Enclosure Panel Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing over a Gang Box Installing on a Flat Surface Installing the Standard Enclosure Panel Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the Add-On Board Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Wiring the Readers Wiring Readers to the Controller BoardFactory Default Configuration Settings for Door IN9 REX IO-TB5 Wiring Door Strikes Or S4 Setting DIP Switches and Jumpers Controller Board DIP Switch and Jumper SettingsNetAXS-123 SW1 DIP Switch Settings S7 a S8 b S9 b S10 SelectionOFF NetAXS-123 SW2 DIP Switch Settings S1a S2a SelectionNetAXS-123 Controller Board Jumpers ExternalAdd-On Board DIP Switch and Jumper Settings Normally Open Normally ClosedSetting the jumpers to configure the relay position 12V ExternalCommunications USB CommunicationsInstalling the NetAXS-123 Panels 2 RS-485 Communications RS-485 Configuration via N-485-PCI-3 RS-485 Configuration via NetAXS-123 Gateway Ethernet TCP/IP Configuration Ethernet TCP/IP CommunicationsSystem Configuration Ethernet ConnectionUSB Connection NetAXS-123 USB ConnectionRS-485 Connection via PCI-3 RS-485 Connection via PCI-3RS-485 Connection via NetAXS-123 Installing the NetAXS-123 Panels PCI3 M-56K Dial-up Modem, RS-485 Connection via Hub PCI-3 56K Dial-up Modem, RS-485 Connection via HubFiber Converter to RS-485 Connection via PCI-3 Fiber Converter to RS-485 Connection via PCI-3Fiber Converter to RS-485 Connection via NetAXS-123 Fiber Converter to RS-485 Connection via NetAXS-123 Installing the NetAXS-123 Panels Ground only one Mixed Loops Hardware Specifications PoE Power LimitationsRelay Contacts Reader InterfaceMechanical Device Element CurrentCable Reader WiringEnvironment Door Egress / Door Lock / Door Status Operation Basic Standalone OperationCard Read / Door Lock Operation Maintenance Problem Solution TroubleshootingTroubleshooting Problems and Solutions Web Technical SupportNormal Support Hours This page is left blank for printing purposes Honeywell Access Systems