Honeywell NETAXS-123 manual Environment, Cable, Reader Wiring

Page 70

Installing the NetAXS-123 Panels

Hardware Specifications

5.6Environment

•Temperature: 0C to 49C operating, -55C to +85C storage.

•Humidity: 5% to 85% RHNC.

5.7Cable

Use industry-standard cables that meet the following specifications:

Table 10: Reader Wiring

Cable Specifications	Description	AWG	Maximum Distance:
			Feet (Meters)

Readers	6 Conductor, Shielded	18	500 (153)

Alarm Input	Twisted Pair, Shielded	18	2,000 (610)

Relay Outputs	Twisted Pair, Shielded	18	2,000 (610)

62www.honeywell.com

Image 70

Contents NetAXS-123 Page Contents RS-485 Connection via PCI-3 RS-485 Connection via NetAXS-123 List of Figures Page List of Tables Page Installing the NetAXS-123 Panels Introduction Access Control OverviewNetAXS-123 Overview NetAXS-123 Compact Enclosure Wiring and Components Panel Components and DescriptionsNetAXS-123 Standard Enclosure Panel Wiring and Components Board Configuration Terminal Block Supervised Input WiringSupervised Input Terminal Blocks Typical Supervised Input Wiring Diagram Supervised Tamper Terminal BlocksNetAXS-123 Input/Output Options NetAXS-123 Access Control UnitNetAXS-123 Add-On Board Board Readers Inputs/OutputsReaders Supported by NetAXS-123 Supported ReadersSeries Reader Model Honeywell Part Number Power Supply Real-Time Clock ProtectionBattery SuppressorsInstalling the Compact Enclosure Panel InstallationInstalling on a Wall Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing over a Gang Box Installing on a Flat Surface Installing the Standard Enclosure Panel Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the Add-On Board Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Wiring the Readers Wiring Readers to the Controller BoardFactory Default Configuration Settings for Door IN9 REX IO-TB5 Wiring Door Strikes Or S4 Setting DIP Switches and Jumpers Controller Board DIP Switch and Jumper SettingsNetAXS-123 SW1 DIP Switch Settings S7 a S8 b S9 b S10 SelectionOFF NetAXS-123 SW2 DIP Switch Settings S1a S2a SelectionNetAXS-123 Controller Board Jumpers ExternalAdd-On Board DIP Switch and Jumper Settings Normally Open Normally ClosedSetting the jumpers to configure the relay position 12V ExternalCommunications USB CommunicationsInstalling the NetAXS-123 Panels 2 RS-485 Communications RS-485 Configuration via N-485-PCI-3 RS-485 Configuration via NetAXS-123 Gateway Ethernet TCP/IP Configuration Ethernet TCP/IP CommunicationsSystem Configuration Ethernet ConnectionUSB Connection NetAXS-123 USB ConnectionRS-485 Connection via PCI-3 RS-485 Connection via PCI-3RS-485 Connection via NetAXS-123 Installing the NetAXS-123 Panels PCI3 M-56K Dial-up Modem, RS-485 Connection via Hub PCI-3 56K Dial-up Modem, RS-485 Connection via HubFiber Converter to RS-485 Connection via PCI-3 Fiber Converter to RS-485 Connection via PCI-3Fiber Converter to RS-485 Connection via NetAXS-123 Fiber Converter to RS-485 Connection via NetAXS-123Installing the NetAXS-123 Panels Ground only one Mixed Loops Relay Contacts Hardware SpecificationsPoE Power Limitations Reader InterfaceMechanical Device Element CurrentEnvironment Reader WiringCable Card Read / Door Lock Operation Basic Standalone OperationDoor Egress / Door Lock / Door Status Operation Maintenance Troubleshooting Problems and Solutions TroubleshootingProblem Solution Normal Support Hours Technical SupportWeb This page is left blank for printing purposes Honeywell Access Systems