Honeywell NETAXS-123 manual RS-485 Configuration via N-485-PCI-3

Page 53

Installing the NetAXS-123 Panels

Installation

DIP switch SW1 positions 8 and 9 are provided for supplying biasing and end-of-line termination for the RS-485 network. The board ships with the switches active. For a Multidrop RS-485 Line, you must turn ON both switch positions 8 and 9 of SW1. (terminated and biased) at the two end-point panels. At all other panels, set DIP switches 8 and 9 in the OFF position. Both switches on a given panel must be set the same. Note that biasing and termination on both ends are present. Use the SW1 positions 8 and 9 ON on both ends of the RS-485 network.

Note: For more information on end of line (EOL) termination, contact Honeywell technical support.

Note: If an RS-485 network has a NetAXS-123 Gateway panel, no N1000-II, N1000-III, N1000-IV, or NS2 are allowed on the same network. If they are added to a network with a NetAXS-123 Gateway panel, they will not be able to communicate with the host computer. In order to use these panels, a N-485-PCI-3 is required, as shown in Figure 9.

Figure 9: RS-485 Configuration via N-485-PCI-3

This configuration supports a combined total of 31 N1000 III, N1000 IV, NetAXS, NetAXS-123, and NS2 panels per Multidrop line.

NetAXS-123 Access Control Unit Installation Guide, Document 800-05779, Revision A

45

Image 53

Contents NetAXS-123 Page Contents RS-485 Connection via PCI-3 RS-485 Connection via NetAXS-123 List of Figures Page List of Tables Page Installing the NetAXS-123 Panels NetAXS-123 Overview Access Control OverviewIntroduction Panel Components and Descriptions NetAXS-123 Compact Enclosure Wiring and ComponentsNetAXS-123 Standard Enclosure Panel Wiring and Components Supervised Input Terminal Blocks Supervised Input WiringBoard Configuration Terminal Block Supervised Tamper Terminal Blocks Typical Supervised Input Wiring DiagramNetAXS-123 Add-On Board NetAXS-123 Access Control UnitNetAXS-123 Input/Output Options Board Readers Inputs/OutputsSeries Reader Model Honeywell Part Number Supported ReadersReaders Supported by NetAXS-123 Real-Time Clock Protection Power SupplySuppressors BatteryInstalling on a Wall InstallationInstalling the Compact Enclosure Panel Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing over a Gang Box Installing on a Flat Surface Installing the Standard Enclosure Panel Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Installing the Add-On Board Installing the NetAXS-123 Panels Installing the NetAXS-123 Panels Wiring Readers to the Controller Board Wiring the ReadersFactory Default Configuration Settings for Door IN9 REX IO-TB5 Wiring Door Strikes Or S4 Controller Board DIP Switch and Jumper Settings Setting DIP Switches and JumpersS7 a S8 b S9 b S10 Selection NetAXS-123 SW1 DIP Switch SettingsOFF S1a S2a Selection NetAXS-123 SW2 DIP Switch SettingsExternal NetAXS-123 Controller Board JumpersNormally Open Normally Closed Add-On Board DIP Switch and Jumper Settings12V External Setting the jumpers to configure the relay position USB Communications CommunicationsInstalling the NetAXS-123 Panels 2 RS-485 Communications RS-485 Configuration via N-485-PCI-3 RS-485 Configuration via NetAXS-123 Gateway Ethernet TCP/IP Communications Ethernet TCP/IP ConfigurationEthernet Connection System ConfigurationNetAXS-123 USB Connection USB ConnectionRS-485 Connection via PCI-3 RS-485 Connection via PCI-3RS-485 Connection via NetAXS-123 Installing the NetAXS-123 Panels PCI3 56K Dial-up Modem, RS-485 Connection via Hub M-56K Dial-up Modem, RS-485 Connection via Hub PCI-3Fiber Converter to RS-485 Connection via PCI-3 Fiber Converter to RS-485 Connection via PCI-3Fiber Converter to RS-485 Connection via NetAXS-123 Fiber Converter to RS-485 Connection via NetAXS-123Installing the NetAXS-123 Panels Ground only one Mixed Loops PoE Power Limitations Hardware SpecificationsRelay Contacts Reader InterfaceDevice Element Current MechanicalCable Reader WiringEnvironment Door Egress / Door Lock / Door Status Operation Basic Standalone OperationCard Read / Door Lock Operation Maintenance Problem Solution TroubleshootingTroubleshooting Problems and Solutions Web Technical SupportNormal Support Hours This page is left blank for printing purposes Honeywell Access Systems