Yamaha YSP-1100 owner manual FCC Information for US customers, Ii En

Page 3

IMPORTANT SAFETY INSTRUCTIONS

FCC INFORMATION (for US customers)

1.IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by YAMAHA may void your authority, granted by the FCC, to use the product.

2.IMPORTANT:

When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3.NOTE:

This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact YAMAHA Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620.

The above statements apply ONLY to those products distributed by YAMAHA Corporation of America or its subsidiaries.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing.

Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.

ii En

Image 3
Contents YSP-1100 Explanation of Graphical Symbols Important Safety InstructionsIi En FCC Information for US customersFor Canadian Customers Iii EnContents Overview Features Using this Manual Cable clamp ⋅1 White/Red Fasteners ⋅4 Supplied AccessoriesRemote control ⋅1 Yellow Optimizer microphone ⋅1 Orange Audio pin cable ⋅1STANDBY/ON Controls and FunctionsFront panel InputFront panel display Rear panel Remote control 10 En 11 En InstallationBefore installing this unit Installing this unitInstallation examples 12 EnExample Using a rack Using a metal wall bracketUsing a stand Using a TV stand14 En Affixing this unitFasteners For video output Connections15 En For audio input For video inputCables used for audio connections Connecting a TV16 En Audio connections Video connectionsConnecting a DVD player/recorder 17 EnDVD player/recorder Video Connecting a VCR18 En Audio connections19 En Connecting a digital satellite tuner or a cable TV tunerConnecting a digital airwave tuner 20 EnDigital airwave tuner CD player, etc Optical digital Output Connecting other external components21 En Cables used for connectionsConnecting a subwoofer 22 EnSubwoofer Monaural Input Rear panel of this unit To the AC outlet Connecting the power supply cableAbout the RS-232C/REMOTE IN/IR-OUT terminals 23 EnGetting Started Installing batteries in the remote controlOperation range of the remote control Close the battery coverFunction-varying buttons Using the remote control Turning on the powerOperational buttons only when YSP is Selected 25 EnOSD screen example Using SET MenuDisplaying the OSD 26 En27 En Flow chart of SET MenuChanging OSD Language Language SetupPress Menu on the remote control Press / to select Language Setup and then press Enter29 En Flow chart of Auto Setup30 En Installing the optimizer microphoneCenter line Using Auto Setup IntelliBeam31 En Assembling the supplied cardboard Microphone stand32 En Auto SetupAuto Setup Start 33 EnBEAM+SOUND Optimz Example Show Result34 En Side view35 En Error messages for Auto SetupBefore the Auto Setup procedure starts While the Auto Setup procedure is in progress36 En Using the System MemorySaving settings Convenient usage of the system memoryPress Enter again Loading settingsSET Menu 37 En1MEMORY Load 38 EnPress / to select Load and then press 39 En Remote control operationsPlayback Selecting the input source40 En Playing back sources41 En Adjusting the volumePress Mute on the remote control to mute the sound Muting the sound42 En Press 5BEAM on the remote control to select the 5 beamEnjoying Surround Sound BeamPress 3BEAM on the remote control to select the 3 beam Stereo plus 3 beam Beam43 En Surround modes and recommended sources Decoder indicatorsStatus Indicator 44 EnEnjoying 2-channel sources Surround sound45 En 46 En Adjusting surround mode parametersWhen Dolby Pro Logic II Music is selected When DTS Neo6 Music is selectedEnjoying Stereo Sound Stereo playback47 En Using auto-adjust function 48 EnMy beam microphone 49 En Using manual-adjust functionPress MY Beam on the remote control Press / while MY Beam is displayed to adjust the angleElements of a sound field Using Sound Field ProgramsWhat is a sound field? 50 En51 En Sound field program descriptions52 En Music programsMovie programs Sports program 53 En54 En Press / on the remote control55 En Using the Volume ModeEffect.LvlMIN Effect.LvlMID Effect.LvlMAX 56 En57 En Press on the remote control58 En Using the Sleep TimerSetting the sleep timer Unit to confirm the setting for the sleep timerCanceling the sleep timer 59 EnDisappears 60 En Manual Setup61 En Using Manual SetupPress / to select Manual Setup and then press Enter Press / / / and Enter to configure each parameter62 En Setting parametersInstalled Position Installed position of this unit 2BEAM Menu63 En Bbeam AdjustmentBeam Adjustment Beam adjustment Installed Height Installed height of this unitBeam Travel Length Beam travel length 64 EnHorizontal Angle Horizontal angle Vertical Angle Vertical angleFront left channel 65 EnFocal Length Focal length Treble Gain Treble gainImage Location Image location 1SOUND MenuCimage Location 66 EnEroom EQ Daudio DelayBsubwoofer SET Cmute Level68 En Input MenuAinput Assignment 1/4 Ainput Assignment 2/4Cinput Trim Binput ModeAinput Assignment 3/4 Ainput Assignment 4/470 En Dimmer SET Dimmer settingsDinput Rename Adimmer SETCunit SET OSD SET OSD settingsUnit SET Unit settings Bosd SET72 En Adjusting the Audio BalanceUsing the test tone Press / to select the channel you want to adjustUsing the audio output being player back Press Test when you have completed all your adjustments73 En 74 En DTS Selecting the Input Mode75 En AutoRelease Input on the front panel Adjusting System ParametersSetting the Memory Protect 76 En77 En Setting the MAX VolumePress / to switch between Protect on Protect OFF Press / to adjust the maximum volume level78 En Setting the Turn on VolumeSetting the Demo Mode Press / to adjust the initial volume levelSetting the Factory Preset Press / to switch between Demo on Demo OFF79 En 80 En Press / to switch between Preset Reset and Preset CancelCode SET Remote Control FeaturesSetting remote control codes 81 EnOperating your DVD player Controlling other components82 En Operating your TV83 En Operating your VCR Operating your STB CATV/Satellite tunerOperation buttons for DVD and VCR Using the TV macro Setting macros for the TV with the tuning capability84 En Operating macros Setting macros for the TV without the tuning capabilityCanceling the macros 85 EnTroubleshooting 86 EnGeneral 87 En 88 En Remote control89 En GlossaryAudio formats Audio information90 En IndexSpeaker Section Specifications91 En AMP SectionDVD Player Cable TV TunerVCR 834 Satellite TunerAll rights reserved On the upper shelf to keep it away from the floor Cables used for connectionsEnjoying surround sound