Yamaha YSP-1100 owner manual Bsubwoofer SET, Cmute Level, Daudio Delay, Eroom EQ, 67 En

Page 71

SUBWOOFER SET (Subwoofer set)

Use to manually adjust various subwoofer settings.

B)SUBWOOFER SET

. BASS OUT;;;;;FRONT

CROSS OVER;;;100Hz

LFE LEVEL;;;;;;0dB

DISTANCE;;;;;;3.0m

[p]/[p]:Up/Down [p]/[p]:Sel [ENTER]:Return

BASS OUT (Bass out)

Low-frequency (bass) signals can be directed to the subwoofer and/or the front left and right channels. This setting also determines the routing of LFE (low-frequency effect) signals found in Dolby Digital or DTS sources. Choices: SWFR (subwoofer), FRONT

Select SWFR if you connect a subwoofer. LFE and low-frequency signals from other channels are directed to the subwoofer.

Select FRONT if you do not use a subwoofer. LFE and low-frequency signals from other channels are directed to the front left and right channels.

CROSS OVER (Cross over)

When BASS OUT is set to SWFR, you can use this feature to select a cross-over (cut-off) frequency for all low-frequency signals. All frequencies below the selected frequency will be sent to the subwoofer speaker position. Choices: 80Hz, 100Hz, 120Hz

LFE LEVEL (Low-frequency effect level)

Select to adjust the output level of the LFE (low-frequency effect) channel according to the capacity of your subwoofer. The LFE channel carries low-frequency special effects which are only added to certain scenes. This setting is effective only when this unit decodes Dolby Digital or DTS signals.

Choices: –20 to 0 dB

DISTANCE (Distance)

Select to adjust the distance of the subwoofer from the listening position.

Choices: 0.3 to 15.0 m

Initial setting: 3.0 m

MANUAL SETUP

MUTE LEVEL (Muting level)

Use to adjust how much the mute function reduces the volume level.

Choices: MUTE, –20 dB

Select MUTE to completely halt all sound output.

Select –20 dB to reduce the current volume level by 20 dB.

C)MUTE LEVEL

pMUTE

-20dB

[p]/[p]:Select [ENTER]:Return

AUDIO DELAY (Audio delay)

Use to delay the sound output and synchronize it with the video image. This may be necessary when using certain LCD monitors or projectors.

Choices: 0 to 160 msec

D)AUDIO DELAY

AUDIO DELAY;;;;;0msec

[p]/[p]:Select [ENTER]:Return

ROOM EQ (Room equalizer)

Use to change the tonal qualities of your listening room when the unit is mounted on the wall.

Choices: MOUNTING (Mount type), REFLECTING (Reflectivity type)

E)ROOM EQ

. MOUNTING;;;;;SHELF REFLECTING;;;NORMAL

[p]/[p]:Up/Down [p]/[p]:Sel [ENTER]:Return

MOUNTING (Mount type)

Use to enhance medium to low range sounds. Choices: WALL (Wall mount), SHELF (Shelf mount)

Select WALL if this unit is mounted on the wall in your listening room.

Select SHELF if this unit is mounted on the shelf in your listening room.

REFLECTING (Reflectivity type)

Use to select the reflectivity of your listening room. Choices: NORMAL (Normal), HI ECHO (High echo)

Select NORMAL if your listening room has a normal reflectivity.

Select HI ECHO if your listening room has highly

reflective surfaces such as concrete walls.

OPERATION

ADVANCED

 

 

English

67 En

Image 71
Contents YSP-1100 Explanation of Graphical Symbols Important Safety InstructionsIi En FCC Information for US customersFor Canadian Customers Iii EnContents Overview Features Using this Manual Cable clamp ⋅1 White/Red Fasteners ⋅4 Supplied AccessoriesRemote control ⋅1 Yellow Optimizer microphone ⋅1 Orange Audio pin cable ⋅1STANDBY/ON Controls and FunctionsFront panel InputFront panel display Rear panel Remote control 10 En 11 En InstallationBefore installing this unit Installing this unitExample Installation examples12 En Using a rack Using a metal wall bracketUsing a stand Using a TV standFasteners 14 EnAffixing this unit For video output Connections15 En For audio input For video inputCables used for audio connections Connecting a TV16 En Audio connections Video connectionsDVD player/recorder Connecting a DVD player/recorder17 En Video Connecting a VCR18 En Audio connections19 En Connecting a digital satellite tuner or a cable TV tunerDigital airwave tuner Connecting a digital airwave tuner20 En CD player, etc Optical digital Output Connecting other external components21 En Cables used for connectionsSubwoofer Monaural Input Rear panel of this unit Connecting a subwoofer22 En To the AC outlet Connecting the power supply cableAbout the RS-232C/REMOTE IN/IR-OUT terminals 23 EnGetting Started Installing batteries in the remote controlOperation range of the remote control Close the battery coverFunction-varying buttons Using the remote control Turning on the powerOperational buttons only when YSP is Selected 25 EnOSD screen example Using SET MenuDisplaying the OSD 26 En27 En Flow chart of SET MenuChanging OSD Language Language SetupPress Menu on the remote control Press / to select Language Setup and then press Enter29 En Flow chart of Auto Setup30 En Installing the optimizer microphoneCenter line Using Auto Setup IntelliBeam31 En Assembling the supplied cardboard Microphone stand32 En Auto SetupBEAM+SOUND Optimz Auto Setup Start33 En Example Show Result34 En Side view35 En Error messages for Auto SetupBefore the Auto Setup procedure starts While the Auto Setup procedure is in progress36 En Using the System MemorySaving settings Convenient usage of the system memoryPress Enter again Loading settingsSET Menu 37 EnPress / to select Load and then press 1MEMORY Load38 En 39 En Remote control operationsPlayback Selecting the input source40 En Playing back sources41 En Adjusting the volumePress Mute on the remote control to mute the sound Muting the sound42 En Press 5BEAM on the remote control to select the 5 beamEnjoying Surround Sound Beam43 En Press 3BEAM on the remote control to select the 3 beamStereo plus 3 beam Beam Surround modes and recommended sources Decoder indicatorsStatus Indicator 44 En45 En Enjoying 2-channel sourcesSurround sound 46 En Adjusting surround mode parametersWhen Dolby Pro Logic II Music is selected When DTS Neo6 Music is selected47 En Enjoying Stereo SoundStereo playback My beam microphone Using auto-adjust function48 En 49 En Using manual-adjust functionPress MY Beam on the remote control Press / while MY Beam is displayed to adjust the angleElements of a sound field Using Sound Field ProgramsWhat is a sound field? 50 En51 En Sound field program descriptionsMovie programs 52 EnMusic programs Sports program 53 En54 En Press / on the remote control55 En Using the Volume ModeEffect.LvlMIN Effect.LvlMID Effect.LvlMAX 56 En57 En Press on the remote control58 En Using the Sleep TimerSetting the sleep timer Unit to confirm the setting for the sleep timerDisappears Canceling the sleep timer59 En 60 En Manual Setup61 En Using Manual SetupPress / to select Manual Setup and then press Enter Press / / / and Enter to configure each parameter62 En Setting parametersInstalled Position Installed position of this unit 2BEAM Menu63 En Bbeam AdjustmentBeam Adjustment Beam adjustment Installed Height Installed height of this unitBeam Travel Length Beam travel length 64 EnHorizontal Angle Horizontal angle Vertical Angle Vertical angleFront left channel 65 EnFocal Length Focal length Treble Gain Treble gainImage Location Image location 1SOUND MenuCimage Location 66 EnEroom EQ Daudio DelayBsubwoofer SET Cmute Level68 En Input MenuAinput Assignment 1/4 Ainput Assignment 2/4Cinput Trim Binput ModeAinput Assignment 3/4 Ainput Assignment 4/470 En Dimmer SET Dimmer settingsDinput Rename Adimmer SETCunit SET OSD SET OSD settingsUnit SET Unit settings Bosd SET72 En Adjusting the Audio BalanceUsing the test tone Press / to select the channel you want to adjust73 En Using the audio output being player backPress Test when you have completed all your adjustments 74 En DTS Selecting the Input Mode75 En AutoRelease Input on the front panel Adjusting System ParametersSetting the Memory Protect 76 En77 En Setting the MAX VolumePress / to switch between Protect on Protect OFF Press / to adjust the maximum volume level78 En Setting the Turn on VolumeSetting the Demo Mode Press / to adjust the initial volume level79 En Setting the Factory PresetPress / to switch between Demo on Demo OFF 80 En Press / to switch between Preset Reset and Preset CancelCode SET Remote Control FeaturesSetting remote control codes 81 EnOperating your DVD player Controlling other components82 En Operating your TVOperation buttons for DVD and VCR 83 EnOperating your VCR Operating your STB CATV/Satellite tuner 84 En Using the TV macroSetting macros for the TV with the tuning capability Operating macros Setting macros for the TV without the tuning capabilityCanceling the macros 85 EnGeneral Troubleshooting86 En 87 En 88 En Remote control89 En GlossaryAudio formats Audio information90 En IndexSpeaker Section Specifications91 En AMP SectionVCR DVD PlayerCable TV Tuner 834 Satellite TunerAll rights reserved On the upper shelf to keep it away from the floor Cables used for connectionsEnjoying surround sound