Panasonic KX-FC238HK manual Handset locator, Cancelling a handset, Cancelling a base unit

Page 76

10. Multi-unit Operation

4Select the desired base unit number, or “Auto”, then press {>}.

L The handset starts searching for the base unit.

10.2.4 Cancelling a handset

A handset can cancel its own registration (or the registration of another handset) that is stored in the base unit. This will allow the base unit to forget the handset.

1Press {j/OK}.

2Select “Base Unit Setup”, then press

{>}.

3Enter “0000” (default base unit PIN).

LIf you changed the PIN, enter it (page 71).

4Enter “335”.

5Select “Cancel Handset”, then press

{>}.

L The numbers of all handsets registered to the base unit are displayed.

6Select the handset(s) you want to cancel, by pressing the desired handset number.

L The selected handset number(s) will flash.

L To cancel a selected handset number, press the number again. The number will stop flashing.

7Press {j/OK}.

8Select “Yes”, then press {>}.

10.2.5 Cancelling a base unit

A handset can cancel a base unit that it is registered to. This allows the handset to forget the base unit.

1Press {j/OK}.

2Select “Handset Setup”, then press {>}.

3Select “Registration”, then press {>}.

4Enter “335”.

5Select “Cancel Base”, then press {>}.

6Enter “0000” (default handset PIN).

LIf you changed the PIN, enter it (page 69).

7Select the base unit(s) you want to cancel, by pressing the desired base unit number.

L The selected base unit number(s) will flash.

L To cancel a selected base unit number, press the number again. The number will stop flashing.

8Press {j/OK}.

9Select “Yes”, then press {>}.

10Press {ih}.

Note:

LTo register the handset to another base unit or to the same base unit again, see manual registration on page 73.

10.2.6Increasing the range of the base unit

You can increase the range of the base unit by using a DECT repeater. Please use only Panasonic DECT repeater. See page 9 for accessory information.

Important:

LBefore registering the repeater to this base unit, you must turn the repeater mode ON.

Setting the repeater mode

1.Press {j/OK}.

2.Select “Base Unit Setup”, then press

{>}.

3.Enter “0000” (default base unit PIN).

LIf you changed the PIN, enter it (page 71).

4.Select “Other Options”, then press {>}.

5.Select “Repeater Mode”, then press {>}.

6.Select “On” or “Off” (default), then press

{>}.

7.Press {ih}.

Note:

LAfter turning repeater mode ON/OFF, you will not be able to make or receive calls for a few moments.

10.3 Handset locator

Using this feature, you can locate the handset if it has been misplaced.

L Keep the front cover page open for button locations.

1 Press {LOCATOR}.

LThe base unit will page the handset for about 1 minute.

2To stop paging, press {LOCATOR} on the base unit or {ih} on the handset.

Note:

LThis feature is not available while using

{DIGITAL SP-PHONE}.

74

Page 75 Page 77
Image 76
Page 75 Page 77
Contents Operating Instructions How to use the operating instructions OpenLocation of Controls Base unitHandset Buttons Listed in alphabetical orderAttach your sales receipt here Important safety instructions Installation BatteryFor best performance Before calling back PhonebookUseful Information Included accessories QuantityAvailable accessories Accessory informationModel No Specifications/Usage Button descriptions of the base unit Button descriptions of the handset Display icons Display descriptions of the handsetDisplay icon Meaning Overview Speaker Receiver Microphone Removing the shipping tapeInk film installation / replacement Installing the ink filmCorrect IncorrectPaper tray Replacing the ink filmRecording paper CorrectIncorrectBattery installation / replacement Installing the batteriesReplacing the batteries Electrolyte Do not mix old and new batteriesConnections Battery charge Battery strengthBattery icons Battery strength Battery lifeTurning the handset power ON/OFF Power onPower OFF Base unit help functionAdjusting handset Adjusting base unit Volume Ringer volumeINT Ring toneDialling mode Date and timeWith the handset With the base unitSystem Setup Press Navi Example 315 PM 12-hour time entry 1. Press 03To correct a mistake SET Date & Time Press SETYour logo Stop Menu FlashKeypad Characters To enter your logo Example BillYour fax number Making phone calls Mute Key lockTo turn key lock OFF, press j/OK for about 2 seconds Digital SP-PHONE MuteINT. Any key answer feature Auto talk featureAnswering phone calls Handset phonebookCategories Making a phone call using the phonebookEditing a stored item One touch dial Erasing stored itemsChain dial Erasing a stored item Base unit phonebookErase Digital SP-PHONE How Caller ID is displayed Caller ID serviceAnother method to erase a stored item Call Waiting Caller ID Handset only Category features for handset phonebookChanging category ring tones Caller ID Viewing and calling back using caller informationFAX/START Digital SP-PHONE Editing a caller’s telephone number before calling back Erasing caller informationInto the handset phonebook Storing caller information into the phonebookInto the base unit phonebook Voice mail service Sending a fax manually Stop Redial FAX/START Digital SP-PHONEDocuments you can send Sending a fax using the base unit phonebook Broadcast transmissionProgramming items into the broadcast memory Adding a new item into the broadcast memoryTo cancel broadcast transmission Erasing a stored item from the broadcast memorySending the same document to pre-programmed parties To send the same document to a one-time group of partiesSelecting the way to use your fax machine Use only as a fax FAX only modeAuto receive Manual receive Use mostly as a telephone TEL modeUse as a telephone and/or Fax Receiving a fax manually Auto answer Activating TEL modeStop FAX/START Digital SP-PHONE Activating TEL/FAX mode TEL/FAX ModeActivating TAM/FAX mode TAM/FAX ModeRing setting in TAM/FAX mode Receiving a fax automatically Auto answer onActivating FAX only mode FAX only ModeActivating the junk fax prohibitor Storing undesired callersTo display the junk fax prohibitor list To print the junk fax prohibitor listUsing with the ring detection feature To use the ring detection feature, set to TEL modeMaking a copy More copying featuresStop Start Setting Recording Original Paper size Document Size DefaultA4, Letter LegalRecording your greeting message Erasing your recorded greeting messageSET MIC Stop Erase GREETING/REC GREETING/CHECK Press GREETING/RECListening to recorded messages Leaving a message for others or yourselfErasing recorded messages SET Stop Erase PlaybackAnswering Machine Operating from a remote location Remote operation using remote commandsSummary of remote operation Turn OFF auto answer setting To turn on the auto answer settingSkip greeting message Recording a marker messageProgramming advanced features Programming basic featuresBase unit programming Basic features Advanced features Code #42 Setting the message alert Code #43 Setting the recording time alertCode #44 Setting the memory reception alert Code #46 Setting friendly receptionCode #58 Setting the scan contrast Code #67 Setting the incoming message monitorCode #68 Setting the Error Correction Mode ECM Code #76 Setting the connecting toneDirect commands for programming features Program code and direct command button#13 Dialling mode OFF #23 Overseas mode#25 Delayed transmission OFF #73 Manual receive mode#76 Connecting tone #78 TEL/FAX ring setting#80 Set default YES OFF #77 Auto answerMenu Sub-menu Default setting Handset programmingMaximum 2300/0600Alarm Night modeProgrammable functions Ringer optionsDisplay setup Call options Other optionsSetting pause length Programmable functions using the base unit PINChanging the flash time Setting call restriction Resetting handset programming that uses the base unit PINStoring/changing emergency numbers Changing the base unit PIN personal identification numberRepeater mode will be retained Operating additional units Registering a handset to a base unitCancelling a handset Cancelling a base unitHandset locator Increasing the range of the base unitExample When handset 1 calls handset Handset Example When handset 1 transfers a call to handset HandsetIntercom between handsets Transferring calls between handsets / Conference callsCopying a stored item Copying handset phonebook itemsCopying all stored items Available character entries for the handset Character entry modesExtended 2 character table O Cyrillic character table PError messages Reports Error messages Base unit display Display Cause and SolutionService personnel Please use genuine Panasonic replacement filmTransmission error occurred. Try again Unnecessary messagesInitial settings When a function does not work, check hereGeneral Problem Cause & Solution Base unit beeps Returns to standby modeProblem Cause & Solution Handset does not Charging but the batteryProblem Cause & Solution Static, sound cuts in/out Documents usingFades. Interference from Other electrical unitsFax sending Fax receivingCopying If a power failure occurs Answering machineWhen the recording paper has jammed in the unit Recording paper jamsCorrect When the recording paper was not fed into the unit properly START1Document jams sending Document feeder / scanner glass cleaning Do not use paper products, such as paper towels or tissuesThermal head cleaning Help Reference lists and reports Base unit only Specifications Duplex procedure RF transmission power Approx mW Operating environmentMass Weight Approx g StandardIndex FAX only TAM/FAX 100 101 102 103 Global web site Copyright PFQX2217ZA CM0905PK02/2
Top Page Image Contents