Agilent Technologies 85032B/E 50 manual Index

Page 53

Index

A

adapters, 1-3part numbers, 6-5

Agilent Technologies, contacting, 5-3

alcohol isopropyl

as cleaning solvent, 3-4altitude, 2-2

B

blank form

standard class assignments, A-3standard definitions, A-6

broadband loads, 1-2

C

cal kit contents, 1-2overview, 1-2

return to Agilent, 5-3serial number, 1-5

calibration bad, 5-2certificate of, 1-3,4-2constants, 1-3

permanently stored, 1-3limited, 1-3,4-3standards, 2-5temperature, 2-2

calibration constants entering, 1-3permanently stored, 1-3

calibration definitions, 1-3calibration kit

contents, 1-2overview, 1-2return to Agilent, 5-3serial number, 1-5

calibration label part number, 6-5

calibration report, 4-2calibration sticker, 4-3center conductor

protrusion, 3-7recession, 3-7

certificate of calibration, 4-2certification

specifications, 2-5characteristics

mechanical, 2-3supplemental, 2-3

class assignment standard, A-2class assignments blank form, A-3

cleaning connectors, 3-4cleaning supplies, 1-3

ordering, 6-5part numbers, 6-5

compressed air or nitrogen, 3-4conductor

mating plane, 2-3

conductor protrusion, 2-3recession, 2-3

connecting the two-piece female open, 3-14

connections, 3-2,3-12,3-15cautions in making, 3-12disconnecting, 3-15ESD concerns, 3-12final, 3-12

how to make, 3-12preliminary, 3-12two-piece female open, 3-14undoing, 3-15

using a torque wrench, 3-12connector

cleaning, 3-4cleaning supplies, 6-5damage, 3-3female, 3-4,3-10gage

dial, 3-7gaging, 3-6

when to do, 3-7life, 3-3

male, 3-8

mating plane, 3-5sex, 1-6threads, 3-4

visual inspection, 3-3wear, 3-3

connector gage handling, 3-8,3-10master, 3-8,3-10reading, 3-7zeroing, 3-8,3-10

connector gage accuracy, 3-6constants

calibration, 1-3entering, 1-3permanently stored, 1-3

contacting Agilent Technologies, 5-3

contents kit, 1-2

D

damage shipment, 1-4

to connectors, 3-3damaged connectors, 3-3data, recertification, 4-2defective connectors, 3-3definitions

standard, A-4

deviation from nominal phase, 2-5device

conductor mating plane, 2-3

connecting, 3-12disconnecting, 3-15handling, 3-15maintenance, 1-6part numbers, 6-5pin depth, 2-3return to Agilent, 5-3storage, 3-15temperature, 2-2visual inspection, 3-3

devices

how Agilent verifies, 4-2serial numbers, 1-5

dial

connector gage, 3-7dimensions

device

center conductor, 2-3outer conductor, 2-3disconnecting the two-piece female open, 3-14

disconnection

two-piece female open, 3-14disconnections, 3-15documentation warranty, ii

E

electrical characteristics supplemental, 2-5

electrical specifications, 2-5electrostatic discharge, 3-2

supplies

part numbers, 6-5

when making connections, 3-12environmental requirements, 2-2equipment

required, 1-3

but not supplied, 1-3,6-2,6-5supplied, 1-2,6-2,6-4

ESD, 3-2precautions, 3-2,3-4supplies

part numbers, 6-5

when making connections, 3-12

F

female open, 3-14

85032B/E

Index-1

Image 53
Contents Agilent Part Number Print Date July User’s and Service GuideDocumentation Warranty Contents Troubleshooting General Information Calibration Kit Overview Kit ContentsCalibration Definitions Installation of the Calibration DefinitionsAdapters OptionsIncoming Inspection Serial Number Record for 85032E Recording the Device Serial NumbersSerial Number Record for 85032B Preventive Maintenance Clarifying the Sex of a ConnectorSpecifications Environmental Requirements Temperature-What to Watch Out ForEnvironmental Requirements Parameter LimitsPin Depth Mechanical CharacteristicsPin Depth Limit Supplemental Electrical Characteristics Electrical SpecificationsElectrical Specifications for 50Ω Type-N Devices Supplemental Electrical CharacteristicsElectrical Specifications 85032B/E Use, Maintenance, and Care of the Devices Electrostatic Discharge ESD Protection SetupVisual Inspection What Causes Connector Wear?Look for Obvious Defects and Damage First Inspect the Mating Plane SurfacesUse Compressed Air or Nitrogen Cleaning ConnectorsInspect Female Connectors Reinspect Clean the Mating Plane SurfacesConnector Gage Accuracy Gaging ConnectorsReading the Connector Gage When to Gage ConnectorsGaging Male Type-N Connectors Gaging ProceduresGaging Male Type-N Connectors Gaging Female Type-N Connectors Gaging Female Type-N Connectors Final Connection Using a Torque Wrench How to Make a ConnectionConnections Preliminary ConnectionWrench Positions Connecting the Two-Piece Female Open Handling and Storage How to Separate a ConnectionHandling and Storage 85032B/E Performance Verification How Agilent Verifies the Devices in This Kit IntroductionRecertification Where to Send a Kit for RecertificationLimited Recertification Option How Often to RecertifyRecertification 85032B/E Troubleshooting Troubleshooting Flowchart Troubleshooting ProcessContacting Agilent Returning a Kit or Device to AgilentReturning a Kit or Device to Agilent 85032B/E Replaceable Parts Replaceable Parts for the 85032B Calibration Kit Protective End Caps for ConnectorsAdapters included with Option 100b Calibration Kit Storage CaseReplaceable Parts for the 85032B Calibration Kit Replaceable Parts for the 85032E Calibration Kit Replaceable Parts-Items Not Included in the Calibration Kit Connector Cleaning SuppliesWrenches ESD Protective DevicesIntroduction 85032B/E Standard Definitions Class Standard Class Label Standard Class AssignmentsTable A-1 Standard Class Assignments Table A-2 Standard Class Assignments Blank Form Blank FormCalibration Kit Label Class Standard ClassNominal Standard Definitions Setting the System ImpedanceSystem Z a = 50 Ω Calibration Kit Label Table A-3 Standard DefinitionsType Min MaxTable A-4 Standard Definitions Blank Form Standardb Offset Freq Number Type 10C0× 10C1× PsDelaySystem Z 0 a = 10C2× 10C3×Index Index-2 85032B/E Index-3