Agilent Technologies 85032B/E 50 manual Table A-4 Standard Definitions Blank Form, System Z 0 a =

Page 52

Standard Definitions

Nominal Standard Definitions

Blank Form

The standard definitions listed in Table A-3may be changed to meet your specific requirements. Table A-4is provided to record the modified standard definitions.

Table A-4 Standard Definitions Blank Form

System Z0a = ______________

Calibration Kit Label: ____________________

Standardb								Offset			Freq
Number	Type	10C0×	10C1×	2	3	c	(ps)Delay	Z	(GLossΩ/s)	(GHz)
Number	Type	10C0×	10C1×	10C2×	10C3×	orFixedSliding	(ps)Delay	Z	(GLossΩ/s)	Min	Max
		F	F/Hz	F/Hz	F/Hz
		15−	27−	36−	45−
								Ω
								0

1

2

3

4

5

6

7

8

a. Ensure system Z0 of network analyzer is set to this value. b. Open, short, load, delay/thru, or arbitrary impedance.

c. Load or arbitrary impedance only.

d. Standard labels that specify sex, (m) or (f), refer to the sex of the analyzer’s test

WaveguideorCoax	LabelStandard
	d

port connector.

A-6

85032B/E

Image 52

Contents User’s and Service Guide Agilent Part Number Print Date JulyDocumentation Warranty Contents Troubleshooting General Information Kit Contents Calibration Kit OverviewInstallation of the Calibration Definitions Calibration DefinitionsAdapters OptionsIncoming Inspection Serial Number Record for 85032B Recording the Device Serial NumbersSerial Number Record for 85032E Clarifying the Sex of a Connector Preventive MaintenanceSpecifications Temperature-What to Watch Out For Environmental RequirementsEnvironmental Requirements Parameter LimitsMechanical Characteristics Pin DepthPin Depth Limit Electrical Specifications Supplemental Electrical CharacteristicsElectrical Specifications for 50Ω Type-N Devices Supplemental Electrical CharacteristicsElectrical Specifications 85032B/E Use, Maintenance, and Care of the Devices ESD Protection Setup Electrostatic DischargeWhat Causes Connector Wear? Visual InspectionLook for Obvious Defects and Damage First Inspect the Mating Plane SurfacesInspect Female Connectors Cleaning ConnectorsUse Compressed Air or Nitrogen Clean the Mating Plane Surfaces ReinspectGaging Connectors Connector Gage AccuracyWhen to Gage Connectors Reading the Connector GageGaging Procedures Gaging Male Type-N ConnectorsGaging Male Type-N Connectors Gaging Female Type-N Connectors Gaging Female Type-N Connectors How to Make a Connection Final Connection Using a Torque WrenchConnections Preliminary ConnectionWrench Positions Connecting the Two-Piece Female Open How to Separate a Connection Handling and StorageHandling and Storage 85032B/E Performance Verification Introduction How Agilent Verifies the Devices in This KitWhere to Send a Kit for Recertification RecertificationLimited Recertification Option How Often to RecertifyRecertification 85032B/E Troubleshooting Troubleshooting Process Troubleshooting FlowchartReturning a Kit or Device to Agilent Contacting AgilentReturning a Kit or Device to Agilent 85032B/E Replaceable Parts Protective End Caps for Connectors Replaceable Parts for the 85032B Calibration KitAdapters included with Option 100b Calibration Kit Storage CaseReplaceable Parts for the 85032B Calibration Kit Replaceable Parts for the 85032E Calibration Kit Connector Cleaning Supplies Replaceable Parts-Items Not Included in the Calibration KitWrenches ESD Protective DevicesIntroduction 85032B/E Standard Definitions Table A-1 Standard Class Assignments Standard Class AssignmentsClass Standard Class Label Blank Form Table A-2 Standard Class Assignments Blank FormCalibration Kit Label Class Standard ClassSetting the System Impedance Nominal Standard DefinitionsTable A-3 Standard Definitions System Z a = 50 Ω Calibration Kit LabelType Min MaxStandardb Offset Freq Number Type 10C0× 10C1× PsDelay Table A-4 Standard Definitions Blank FormSystem Z 0 a = 10C2× 10C3×Index Index-2 85032B/E Index-3