Agilent Technologies 85032B/E 50 manual Table A-3 Standard Definitions, Type, Min Max

Page 51

Standard Definitions

Nominal Standard Definitions

Table A-3 Standard Definitions

System Z a = 50 Ω	Calibration Kit Label:	Ω
0	Calibration Kit Label:	N 50

Number	Type	10C0×	10C1×	10C2×	10C3×	SlidingorFixed	(ps)Delay	Z		/s)(LossΩ	Min		Max	WaveguideorCoax	LabelStandard
Standardb				2	3	c		Offset				Freq			d
				2	3	c						(GHz)			d
			F/Hz	F/Hz	F/Hz							(GHz)
		F
		F
		−15	−27	−36	−45
								Ω
								0

1	Short						0.093	49.992		700Μ	0		999	Coax	Short (m)

2	Open	119.09	−36.955	26.258	5.5136		0	50		700Μ	0		999	Coax	Open (m)

3	Load					Fixed	0	50		700Μ	0		999	Coax	Broad-
															band

4	Delay/						0	50		700Μ	0		999	Coax	Thru
	Thru

5

6

7	Short						17.817	50.209		2.1002G	0		999	Coax	Short (f)

8	Open	62.140	−143.07	82.920	0.7600		17.411	50		700Μ	0		999	Coax	Open (f)

a.Ensure system impedance (Z0) of network analyzer is set to this value.

b.Open, short, load, delay/thru, or arbitrary impedance.

c.Load or arbitrary impedance only.

d.Standard labels that specify sex, (m) or (f), refer to the sex of the analyzer’s test port connector.

85032B/E

A-5

Image 51

Contents Agilent Part Number Print Date July User’s and Service GuideDocumentation Warranty Contents Troubleshooting General Information Calibration Kit Overview Kit ContentsOptions Installation of the Calibration DefinitionsCalibration Definitions AdaptersIncoming Inspection Recording the Device Serial Numbers Serial Number Record for 85032BSerial Number Record for 85032E Preventive Maintenance Clarifying the Sex of a ConnectorSpecifications Parameter Limits Temperature-What to Watch Out ForEnvironmental Requirements Environmental RequirementsPin Depth Mechanical CharacteristicsPin Depth Limit Supplemental Electrical Characteristics Electrical SpecificationsSupplemental Electrical Characteristics Electrical Specifications for 50Ω Type-N DevicesElectrical Specifications 85032B/E Use, Maintenance, and Care of the Devices Electrostatic Discharge ESD Protection SetupInspect the Mating Plane Surfaces What Causes Connector Wear?Visual Inspection Look for Obvious Defects and Damage FirstCleaning Connectors Inspect Female ConnectorsUse Compressed Air or Nitrogen Reinspect Clean the Mating Plane SurfacesConnector Gage Accuracy Gaging ConnectorsReading the Connector Gage When to Gage ConnectorsGaging Male Type-N Connectors Gaging ProceduresGaging Male Type-N Connectors Gaging Female Type-N Connectors Gaging Female Type-N Connectors Preliminary Connection How to Make a ConnectionFinal Connection Using a Torque Wrench ConnectionsWrench Positions Connecting the Two-Piece Female Open Handling and Storage How to Separate a ConnectionHandling and Storage 85032B/E Performance Verification How Agilent Verifies the Devices in This Kit IntroductionHow Often to Recertify Where to Send a Kit for RecertificationRecertification Limited Recertification OptionRecertification 85032B/E Troubleshooting Troubleshooting Flowchart Troubleshooting ProcessContacting Agilent Returning a Kit or Device to AgilentReturning a Kit or Device to Agilent 85032B/E Replaceable Parts Calibration Kit Storage Case Protective End Caps for ConnectorsReplaceable Parts for the 85032B Calibration Kit Adapters included with Option 100bReplaceable Parts for the 85032B Calibration Kit Replaceable Parts for the 85032E Calibration Kit ESD Protective Devices Connector Cleaning SuppliesReplaceable Parts-Items Not Included in the Calibration Kit WrenchesIntroduction 85032B/E Standard Definitions Standard Class Assignments Table A-1 Standard Class AssignmentsClass Standard Class Label Standard Class Blank FormTable A-2 Standard Class Assignments Blank Form Calibration Kit Label ClassNominal Standard Definitions Setting the System ImpedanceMin Max Table A-3 Standard DefinitionsSystem Z a = 50 Ω Calibration Kit Label Type10C2× 10C3× Standardb Offset Freq Number Type 10C0× 10C1× PsDelayTable A-4 Standard Definitions Blank Form System Z 0 a =Index Index-2 85032B/E Index-3