Agilent Technologies 85032B/E 50 manual Contents

Page 3

Contents

1. General Information

 

Calibration Kit Overview

1-2

Kit Contents

1-2

Broadband Loads

1-2

Opens and Shorts

1-2

Adapters

1-3

Calibration Definitions

1-3

Installation of the Calibration Definitions

1-3

Options

1-3

Equipment Required but Not Supplied

1-3

Incoming Inspection

1-4

Recording the Device Serial Numbers

1-5

Clarifying the Sex of a Connector

1-6

Preventive Maintenance

1-6

2. Specifications

Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

Temperature—What to Watch Out For . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

Mechanical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

Pin Depth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5

Certification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5

Supplemental Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5

3. Use, Maintenance, and Care of the Devices

 

Electrostatic Discharge

.3-2

Visual Inspection

.3-3

Look for Obvious Defects and Damage First

.3-3

What Causes Connector Wear?

.3-3

Inspect the Mating Plane Surfaces

.3-3

Inspect Female Connectors

.3-4

Cleaning Connectors

.3-4

Gaging Connectors

.3-6

Connector Gage Accuracy

.3-6

When to Gage Connectors

.3-7

Reading the Connector Gage

.3-7

Gaging Procedures

.3-8

Gaging Male Type-N Connectors

.3-8

Gaging Female Type-N Connectors

3-10

Connections

3-12

How to Make a Connection

3-12

Preliminary Connection

3-12

Final Connection Using a Torque Wrench

3-12

Connecting and Disconnecting the Two-Piece Female Open (85032B)

3-14

How to Separate a Connection

3-15

Handling and Storage

3-15

85032B/E

iii

Image 3
Contents Agilent Part Number Print Date July User’s and Service GuideDocumentation Warranty Contents Troubleshooting General Information Calibration Kit Overview Kit ContentsOptions Installation of the Calibration DefinitionsCalibration Definitions AdaptersIncoming Inspection Recording the Device Serial Numbers Serial Number Record for 85032BSerial Number Record for 85032E Preventive Maintenance Clarifying the Sex of a ConnectorSpecifications Parameter Limits Temperature-What to Watch Out ForEnvironmental Requirements Environmental RequirementsPin Depth Mechanical CharacteristicsPin Depth Limit Supplemental Electrical Characteristics Electrical SpecificationsSupplemental Electrical Characteristics Electrical Specifications for 50Ω Type-N DevicesElectrical Specifications 85032B/E Use, Maintenance, and Care of the Devices Electrostatic Discharge ESD Protection SetupInspect the Mating Plane Surfaces What Causes Connector Wear?Visual Inspection Look for Obvious Defects and Damage FirstCleaning Connectors Inspect Female ConnectorsUse Compressed Air or Nitrogen Reinspect Clean the Mating Plane SurfacesConnector Gage Accuracy Gaging ConnectorsReading the Connector Gage When to Gage ConnectorsGaging Male Type-N Connectors Gaging ProceduresGaging Male Type-N Connectors Gaging Female Type-N Connectors Gaging Female Type-N Connectors Preliminary Connection How to Make a ConnectionFinal Connection Using a Torque Wrench ConnectionsWrench Positions Connecting the Two-Piece Female Open Handling and Storage How to Separate a ConnectionHandling and Storage 85032B/E Performance Verification How Agilent Verifies the Devices in This Kit IntroductionHow Often to Recertify Where to Send a Kit for RecertificationRecertification Limited Recertification OptionRecertification 85032B/E Troubleshooting Troubleshooting Flowchart Troubleshooting ProcessContacting Agilent Returning a Kit or Device to AgilentReturning a Kit or Device to Agilent 85032B/E Replaceable Parts Calibration Kit Storage Case Protective End Caps for ConnectorsReplaceable Parts for the 85032B Calibration Kit Adapters included with Option 100bReplaceable Parts for the 85032B Calibration Kit Replaceable Parts for the 85032E Calibration Kit ESD Protective Devices Connector Cleaning SuppliesReplaceable Parts-Items Not Included in the Calibration Kit WrenchesIntroduction 85032B/E Standard Definitions Standard Class Assignments Table A-1 Standard Class AssignmentsClass Standard Class Label Standard Class Blank FormTable A-2 Standard Class Assignments Blank Form Calibration Kit Label ClassNominal Standard Definitions Setting the System ImpedanceMin Max Table A-3 Standard DefinitionsSystem Z a = 50 Ω Calibration Kit Label Type10C2× 10C3× Standardb Offset Freq Number Type 10C0× 10C1× PsDelayTable A-4 Standard Definitions Blank Form System Z 0 a =Index Index-2 85032B/E Index-3