Agilent Technologies 85032B/E 50 manual Replaceable Parts for the 85032B Calibration Kit

Page 42

Replaceable Parts

Introduction

Introduction

Table 6-1lists the replacement part numbers for items included in the 85032B calibration kit and Figure 6-1illustrates each of these items.

Table 6-2lists the replacement part numbers for items included in the 85032E calibration kit and Figure 6-2illustrates each of these items.

Table 6-3lists the replacement part numbers for items recommended or required for successful operation but not included in the calibration kit.

To order a listed part, note the description, the part number, and the quantity desired. Telephone or send your order to Agilent Technologies. See Table 5-1 on page 5-3.

Table 6-1 Replaceable Parts for the 85032B Calibration Kit

Item No.

Description

Qty Per Kit

Agilent Part Number

 

 

 

 

 

Calibration Devices (50Ω Type-N)

 

 

 

 

 

1

Male broadband load

1

00909-60009

 

 

 

 

2

Female broadband load

1

00909-60010

 

 

 

 

3

Male short

1

85032-60008

 

 

 

 

4

Female short

1

85032-60009

 

 

 

 

5

Male open

1

85032-60007

 

 

 

 

6

Female opena

1

85032-60012

 

Adapters (included with Option 100)b

 

7

Type-N-male to 7-mm

2

85054-60009

 

 

 

 

8

Type-N-female to 7-mm

2

85054-60001

 

 

 

 

 

Calibration Kit Storage Case

 

 

 

 

 

9

Box assembly (includes case and foam pad set)

1

85032-60010

 

 

 

 

10

Case (without foam pad set)c

1

85032-80002

11

Foam pad setc

1

85032-80003

 

Protective End Caps for Connectors

 

 

 

 

 

12

Female end cap for type-N

as required

1401-0225

 

 

 

 

13

Male end cap for type-N and 7 mm

as required

1401-0214

 

 

 

 

 

Miscellaneous Items

 

 

 

 

 

 

15

User’s and service guide

1

85032-90020

 

 

 

 

a.Includes center conductor extender.

b.Refer to “Options” on page 1-3for description of available options.

c.Included in box assembly.

6-2

85032B/E

Page 41 Page 43
Image 42
Page 41 Page 43
Contents User’s and Service Guide Agilent Part Number Print Date JulyDocumentation Warranty Contents Troubleshooting General Information Kit Contents Calibration Kit OverviewAdapters Installation of the Calibration DefinitionsCalibration Definitions OptionsIncoming Inspection Recording the Device Serial Numbers Serial Number Record for 85032BSerial Number Record for 85032E Clarifying the Sex of a Connector Preventive MaintenanceSpecifications Environmental Requirements Temperature-What to Watch Out ForEnvironmental Requirements Parameter LimitsMechanical Characteristics Pin DepthPin Depth Limit Electrical Specifications for 50Ω Type-N Devices Electrical SpecificationsSupplemental Electrical Characteristics Supplemental Electrical CharacteristicsElectrical Specifications 85032B/E Use, Maintenance, and Care of the Devices ESD Protection Setup Electrostatic DischargeLook for Obvious Defects and Damage First What Causes Connector Wear?Visual Inspection Inspect the Mating Plane SurfacesCleaning Connectors Inspect Female ConnectorsUse Compressed Air or Nitrogen Clean the Mating Plane Surfaces ReinspectGaging Connectors Connector Gage AccuracyWhen to Gage Connectors Reading the Connector GageGaging Procedures Gaging Male Type-N ConnectorsGaging Male Type-N Connectors Gaging Female Type-N Connectors Gaging Female Type-N Connectors Connections How to Make a ConnectionFinal Connection Using a Torque Wrench Preliminary ConnectionWrench Positions Connecting the Two-Piece Female Open How to Separate a Connection Handling and StorageHandling and Storage 85032B/E Performance Verification Introduction How Agilent Verifies the Devices in This KitLimited Recertification Option Where to Send a Kit for RecertificationRecertification How Often to RecertifyRecertification 85032B/E Troubleshooting Troubleshooting Process Troubleshooting FlowchartReturning a Kit or Device to Agilent Contacting AgilentReturning a Kit or Device to Agilent 85032B/E Replaceable Parts Adapters included with Option 100b Protective End Caps for ConnectorsReplaceable Parts for the 85032B Calibration Kit Calibration Kit Storage CaseReplaceable Parts for the 85032B Calibration Kit Replaceable Parts for the 85032E Calibration Kit Wrenches Connector Cleaning SuppliesReplaceable Parts-Items Not Included in the Calibration Kit ESD Protective DevicesIntroduction 85032B/E Standard Definitions Standard Class Assignments Table A-1 Standard Class AssignmentsClass Standard Class Label Calibration Kit Label Class Blank FormTable A-2 Standard Class Assignments Blank Form Standard ClassSetting the System Impedance Nominal Standard DefinitionsType Table A-3 Standard DefinitionsSystem Z a = 50 Ω Calibration Kit Label Min MaxSystem Z 0 a = Standardb Offset Freq Number Type 10C0× 10C1× PsDelayTable A-4 Standard Definitions Blank Form 10C2× 10C3×Index Index-2 85032B/E Index-3
Top Page Image Contents