a/d/s/ iSeries manual Enter Output 1 Menu, Self Submenu, MINIMUM/PERCENT LOW Submenu

Page 37

ENTER OUTPUT 1 MENU:

Press a 1) Press a, if necessary, until CNFG prompt appears. Press d 2) Display advances to INPT Input Menu.

Press a 3) Press a, if necessary, until Display advances to OUT1 Output 1 Menu.

Press d 4) Display advances to SELF Self Submenu.

SELF SUBMENU:

The Self Option allows the output of the instrument to be controlled manually from the front panel.

Press d 5) Display flashes the current setting of Self, ENBL Enabled or DSBL Disabled.

Press b 6) Press the b button to select between Enable and Disable. Press d 7) If Self ENBL Enabled was selected, display shows STRD stored message momentarily and then advances to the next

menu (Output 1 setting is completed).

The output is now under the direct control of the operator and can be adjusted in the Run Mode (M00.0 to M99.9), by

pressing the b and c buttons, where M calls for the Manual (Self) Control. For example, setting of M50.0 of an Output make it ON 50% of the time.

8)If Self DSBL Disabled was selected, display shows STRD stored message momentarily and then advances to oPLO

Minimum/Percent Low Submenu of Output 1 Menu.

There is a shorter way to Enable or Disable Self Mode. From a Run Mode, press d and then press a. Self Mode is Enabled now. Press b or c to display MXX.X. To disable Self, press d and then press a. Display goes to the Run Mode. Self Mode is Disabled now.

MINIMUM/PERCENT LOW SUBMENU:

Specify in percent, the minimum value (0000) for control output. If the output is time proportional (Relay, SSR or Pulse), then the minimum duty-cycle, in percent, is specified.

Press d 9) Display flashes 1st digit of previous “Percent Low” setting. Press b & c 10) Use b and c buttons to enter a new value for “Percent Low”. Press d 11) Display shows STRD stored message momentarily and then

advances to oPHI Maximum/Percent High Submenu.

33

Image 37

Contents Newport Electronics,Inc Newport Electronics,Inc Table of Contents Input Properties Factory Preset Values Flow Chart for Alarm 1 Menu Flow Chart for Alarm 2 MenuList of Figures List of TablesTIP Description Part IntroductionEMC Considerations Safety ConsiderationsBefore You Begin Optional Remote Programmer Front Panel Part SetupFront Panel Connections PowerInput OutputMain Power Connections Fuse Requirement see specifications Electrical Installation Power ConnectionsThermocouple Input Thermocouple Wiring Hookup TC Wire Color ChartOhm Wiring Hookup 3 Two/Three/Four-Wire RTDProcess Voltage Process CurrentIsolated Analog Output Wiring Hookup Wiring Outputs10 Snubber Circuits Wiring Hookup 13 Excitation Output Button Function in Configuration Mode Operation Configuration Mode IntroductionPart Flow Chart for ID and Set Points Menu ConfigurationEntering Your NON-DEFAULT SETPOINT/ID Security ID Number Entering Your NON-DEFAULT Full Security ID NumberID Number Setpoint Set PointsEnter Configuration Menu Configuration MenuInput Type Menu Enter Input Type Menu Input Type ThermocoupleThermocouple Submenu Thermocouple TypesRTD Submenu Input Type RTDRTD Types RTD Value SubmenuInput Type Process Reading Configuration MenuProcess Submenu Process TypesTemperature Unit Submenu Enter Reading Configuration MenuDecimal Point Submenu Filter Constant SubmenuINPUT/READING Scale and Offset Submenu Reading Configuration If Process was selectedRange Conversion Number Conversion TableEnter Alarm 1 Menu AlarmAlarm 1 ABSOLUTE/DEVIATION Submenu Alarm 1 ENABLE/DISABLE SubmenuAlarm 1 LATCH/UNLATCH Submenu Active Submenu Contact Closure SubmenuAlarm 1 LOW Value Submenu Alarm ENABLE/DISABLE AT Power onAlarm 1 HI Value Submenu Enter Alarm 2 Menu Loop Break Time/Field Calibration Loop Break ENABLE/DISABLE SubmenuEnter Loop Break Time Menu Loop Break Time Value SubmenuSetpoint Deviation ENABLE/DISABLE Submenu Reading Adjust SubmenuThermocouple Field Calibration Submenu Output Flow Chart for OutputSelf Submenu Enter Output 1 MenuMINIMUM/PERCENT LOW Submenu Control Type Output Relay, SSR, or Pulse MAXIMUM/PERCENT High SubmenuAction Type Submenu Anti Integral Submenu Auto PID SubmenuProportional Band Submenu Start Auto Tune PIDRate Setup Submenu Reset Setup SubmenuCycle Time Submenu Deadband Submenu Damping Factor SubmenuEnter Analog Output Menu Analog Output RetransmissionCURRENT/VOLTAGE Submenu OUT ReadingSoak ENABLE/DISABLE Submenu Ramp ENABLE/DISABLE SubmenuRamp & Soak Enter Ramp and Soak MenuSoak Value Submenu Ramp Value SubmenuID Code Entering or Changing Your NON-DEFAULT ID CodeEnter ID Code Menu Full Security Level Submenu Entering or Changing Your Default ID CodeSETPOINT/ID Security Level Submenu Communication Option 12 Flow Chart for Communication OptionCommunication Parameters Submenu Enter Communication Option MenuBaud Submenu Parity SubmenuBUS Format Submenu Stop BIT SubmenuModbus Protocol Submenu Line Feed SubmenuCommunication Interface Standard Submenu Data Flow Mode SubmenuData Separation Character Submenu Data Format Submenu Alarm Status SubmenuMain Reading Submenu Peak Value SubmenuAddress Value Submenu Address Setup SubmenuTransmit Time Interval Submenu Transmit Time Interval Value SubmenuDisplay Color Selection Alarm 1 Display Color SubmenuEnter Display Color Selection Menu Normal Color Display SubmenuExample Alarm 2 Display Color SubmenuDisplay Colors change sequences Green RED AmberAmber RED Green Part Specifications Control Output ControlSSR CommunicationsInsulation ExcitationGeneral Input Type Range Accuracy Input PropertiesFactory preset value Part 5 Factory Preset ValuesDisplay Color Colr Measurement Category Part CE Approvals InformationPage Page Page Warranty/Disclaimer M4165/N/0206