Ricoh AP505 manual Bypass tray, Paper Tray

Page 20

Getting Acquainted

10.Bypass tray

Use to print on to thick paper, OHP trans- parencies and adhesive labels in addition to plain paper.

1	11. Paper Tray

Load paper into this tray for printing.

2

Image 20

Contents Printer Reference Overseas Affiliates Page Means Power ON. b means Power OFF Page Means Power ON. b means Power OFF Page Means Power ON. b means Power OFF Trademarks Safety Information Safety During OperationIii Page Energy Star Program Low-power mode Energy Save modeSpecifications Manuals for Your Printer Manuals for Your PrinterHow to Read this Manual SymbolsTable of Contents Cleaning the Printer Moving and Transporting the Printer SpecificationsReplacing Consumables ConsumablesPage Guide to the Printer Exterior-Front ViewBypass tray Paper TrayExterior-Rear View Interior Operation Panel Turning the Printer On and Off Turning On the PrinterTurning Off the Printer ReadyInstalling Options Available Options Memory Unit Type505 ⇒ P.9Installing the Memory Unit Type505 Dimm For more information on Installing the Printer Hard Disk Type505 Check the contents of the box for the following itemsPress Enter Press Enter to Initialize DiskInitializing Installing the Paper Feed Unit Type305 Move the printer to make install- ing spaceRemove both pieces of adhesive tape Pull out the paper tray, and re- move the paddingRemove the ring attached to the red tag Place the printer on the paper feed unitPaper and Other Media Supported by this Printer Paper Types and SizesPaper Sizes Metric version B6 JIS⇒ P.27 Loading Paper in the Bypass Tray Paper Sizes Inch version ⇒ P.27 Loading Paper in the Bypass Tray Precautions for Paper Paper types and cautions Plain paperThick Paper Adhesive labelsOHP transparencies Paper not supported by this printer Printable Area Load paper into the tray with the print side up Loading PaperLoading Paper in the Paper Tray Printer Setup Specifying paper size using the operation panelSET * Size TRAY1 * SizeLoading Paper in the Bypass Tray Open the bypass traySlide the side guides Load paper until it stops with the print side downPress Enter until Bypass Tray Size appears Sliding out the Output Tray ExtenderBypass Tray Size Troubleshooting Error & Status Messages on the Operation Panel⇒ P.38 Removing Misfed Pa Tle. ⇒ P.53 Replacing Waste Toner Bottle and Charg Possible Cause Solutions Printer Doesnt PrintNetwork Connection If the printer is using the I/O timeout settingTerface cable Windows 95/98 Windows NT4.0Other Printing Problems Status Possible Causes, Descriptions, and SolutionsTions for Paper Ing the Charger Removing Misfed Paper When the Message Open AppearsMisfeed Appears Bypass trayOpen the paper exit cover When the Message RemoveTray Appears Close the paper exit cover Close the front cover Remove the misfed paper from inside of the printerRemove the misfed paper from Cleaning the Charger Cleaning the PrinterCleaning the Friction Pad Cleaning the Dust-proofing glass Remove the cleaning brush from back of the front coverTFWX280E Slide the lock lever up Replacing ConsumablesOpen the left cover Remove the protective sheet from the new toner cartridge Hold the new toner cartridgeShake it with a horizontal motion About 10 times, as shown in the il- lustrationMaintenance Magenta TonerMagenta Toner Please Wait Replace Toner MagentaReplace PCU Turn off the printers power switchReplacing the Photoconductor Unit TFWX400E Fuser OIL LOW ADD Fuser OIL Turn on the printer’s power switchReplacing the Fuser Oil Bottle and Ozone Filter Remove the green cap from the new oil bottle Close the fuser oil bottle coverInsert a new ozone filter into the printer Waste Toner Almost Full Replacing the Waste Toner Bottle and ChargerLocks release, and the charg- er is lifted slightly Appendix Moving and Transporting the PrinterSpecifications MainframeNoise Emission Sound Power Level DimensionsWeight Warm-up TimeOptional Equipment Options Consumables Toner CartridgeService Life *1 Other ConsumablesIndex