Ricoh AP505 manual Installing the Printer Hard Disk Type505

Page 29

Installing the Printer Hard Disk Type505

Installing the Printer Hard Disk Type505

RCAUTION:

•Make sure to turn off the printer and wait for about 30 minutes before installing options. Not waiting for the printer to cool down can result in a burn.

Note

❒For this printer, use only Printer Hard Disk Type505.

ACheck the contents of the box for the following items.

•Printer Hard Disk Type505

•Installation Guide

•Screws (3 pcs)

BTurn off the printer's power switch and remove all cables and cords from the printer.

CRemove screws and remove the back plate.

TFWX186E

Note

DMake sure that the projection of the connector of the hard disk is on the top. Attach the connector to the slot while holding the hard

disk.2

TFWX600E

ESet the hard disk in the lower left corner at the rear of the printer, as shown in the illustration. Make sure that the screw holes of the hard disk align with the screw holes of the printer. And fasten it with the screws that are enclosed in the box using the screw driver.

TFWX610E

❒A coin can be used to remove the screws.

11

Image 29

Contents Printer Reference Overseas Affiliates Page Means Power ON. b means Power OFF Page Means Power ON. b means Power OFF Page Means Power ON. b means Power OFF Trademarks Safety During Operation Safety InformationIii Page Energy Star Program Low-power mode Energy Save modeSpecifications Manuals for Your Printer Manuals for Your PrinterSymbols How to Read this ManualTable of Contents Moving and Transporting the Printer Specifications Cleaning the PrinterReplacing Consumables ConsumablesPage Exterior-Front View Guide to the PrinterPaper Tray Bypass trayExterior-Rear View Interior Operation Panel Turning On the Printer Turning the Printer On and OffTurning Off the Printer ReadyInstalling Options Memory Unit Type505 ⇒ P.9 Available OptionsInstalling the Memory Unit Type505 Dimm For more information on Check the contents of the box for the following items Installing the Printer Hard Disk Type505Press Enter Press Enter to Initialize DiskInitializing Move the printer to make install- ing space Installing the Paper Feed Unit Type305Pull out the paper tray, and re- move the padding Remove both pieces of adhesive tapeRemove the ring attached to the red tag Place the printer on the paper feed unitPaper Types and Sizes Paper and Other Media Supported by this PrinterB6 JIS Paper Sizes Metric version⇒ P.27 Loading Paper in the Bypass Tray Paper Sizes Inch version ⇒ P.27 Loading Paper in the Bypass Tray Paper types and cautions Plain paper Precautions for PaperAdhesive labels Thick PaperOHP transparencies Paper not supported by this printer Printable Area Load paper into the tray with the print side up Loading PaperLoading Paper in the Paper Tray Specifying paper size using the operation panel Printer SetupSET * Size TRAY1 * SizeOpen the bypass tray Loading Paper in the Bypass TraySlide the side guides Load paper until it stops with the print side downPress Enter until Bypass Tray Size appears Sliding out the Output Tray ExtenderBypass Tray Size Error & Status Messages on the Operation Panel Troubleshooting⇒ P.38 Removing Misfed Pa Tle. ⇒ P.53 Replacing Waste Toner Bottle and Charg Printer Doesnt Print Possible Cause SolutionsNetwork Connection If the printer is using the I/O timeout settingTerface cable Windows NT4.0 Windows 95/98Status Possible Causes, Descriptions, and Solutions Other Printing ProblemsTions for Paper Ing the Charger Removing Misfed Paper Appears When the Message OpenMisfeed Appears Bypass trayOpen the paper exit cover When the Message RemoveTray Appears Close the paper exit cover Close the front cover Remove the misfed paper from inside of the printerRemove the misfed paper from Cleaning the Charger Cleaning the PrinterCleaning the Friction Pad Remove the cleaning brush from back of the front cover Cleaning the Dust-proofing glassTFWX280E Slide the lock lever up Replacing ConsumablesOpen the left cover Hold the new toner cartridge Remove the protective sheet from the new toner cartridgeShake it with a horizontal motion About 10 times, as shown in the il- lustrationMagenta Toner MaintenanceMagenta Toner Please Wait Replace Toner MagentaReplace PCU Turn off the printers power switchReplacing the Photoconductor Unit TFWX400E Fuser OIL LOW ADD Fuser OIL Turn on the printer’s power switchReplacing the Fuser Oil Bottle and Ozone Filter Close the fuser oil bottle cover Remove the green cap from the new oil bottleInsert a new ozone filter into the printer Replacing the Waste Toner Bottle and Charger Waste Toner Almost FullLocks release, and the charg- er is lifted slightly Moving and Transporting the Printer AppendixMainframe SpecificationsDimensions Noise Emission Sound Power LevelWeight Warm-up TimeOptional Equipment Options Toner Cartridge ConsumablesOther Consumables Service Life *1Index