Ricoh AP505 manual Tle. ⇒ P.53 Replacing Waste Toner Bottle and Charg

Page 49

 

Error & Status Messages on the Operation Panel

 

 

 

 

 

 

Message

Description

Comments

 

 

 

 

 

 

 

REPLACE PCU

The photoconductor unit is

If printed side gets dirty, re-

 

 

 

nearly at the end of its life.

place the photoconductor

 

 

 

 

unit. ⇒ P.48 “Replacing the

 

 

 

 

Photoconductor Unit”

 

 

 

 

 

 

 

TONER LOW

Indicated toner is low or

Replace the indicated toner

 

 

xxx

runs out.

cartridge. ⇒ P.45 “Replacing

 

 

 

the Toner Cartridge”

 

 

 

 

 

 

 

 

 

 

 

WARMING UP

The printer is preparing for

Wait until the printer is

 

 

 

printing.

warmed up.

 

 

 

 

 

 

 

 

The printer adjusts itself

It is not an error message.

 

 

 

regularly to maintain print

The printer is working prop-

 

 

 

quality. (This message

 

 

 

 

 

 

 

erly. Just wait a while.

 

4

 

might appear while print-

 

 

 

 

 

ing.)

 

 

 

 

 

 

 

 

WASTE TONER

The waste toner bottle is

Replace the waste toner bot-

 

 

ALMOST FULL

nearly full.

tle. ⇒ P.53 “Replacing the

 

 

 

Waste Toner Bottle and Charg-

 

 

 

 

 

 

 

 

er”

 

 

 

 

 

 

 

WASTE TONER

The waste toner bottle is

Replace the waste toner bot-

 

 

FULL

full.

tle. ⇒ P.53 “Replacing the

 

 

 

Waste Toner Bottle and Charg-

 

 

 

 

 

 

 

 

er”

 

 

 

 

 

 

 

Note

❒If you cannot solve the problem by taking above actions, turn the printer power off and then back on again. If this doesn't clear the error message, write down the error number and the message, and contact your sales or service representative.

31

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Printer Reference Overseas Affiliates Page Means Power ON. b means Power OFF Page Means Power ON. b means Power OFF Page Means Power ON. b means Power OFF Trademarks Safety During Operation Safety InformationIii Page Specifications Low-power mode Energy Save modeEnergy Star Program Manuals for Your Printer Manuals for Your PrinterSymbols How to Read this ManualTable of Contents Moving and Transporting the Printer Specifications Cleaning the PrinterReplacing Consumables ConsumablesPage Exterior-Front View Guide to the PrinterPaper Tray Bypass trayExterior-Rear View Interior Operation Panel Turning On the Printer Turning the Printer On and OffTurning Off the Printer ReadyInstalling Options Memory Unit Type505 ⇒ P.9 Available OptionsInstalling the Memory Unit Type505 Dimm For more information on Check the contents of the box for the following items Installing the Printer Hard Disk Type505Initializing Press Enter to Initialize DiskPress Enter Move the printer to make install- ing space Installing the Paper Feed Unit Type305Pull out the paper tray, and re- move the padding Remove both pieces of adhesive tapeRemove the ring attached to the red tag Place the printer on the paper feed unitPaper Types and Sizes Paper and Other Media Supported by this PrinterB6 JIS Paper Sizes Metric version⇒ P.27 Loading Paper in the Bypass Tray Paper Sizes Inch version ⇒ P.27 Loading Paper in the Bypass Tray Paper types and cautions Plain paper Precautions for PaperAdhesive labels Thick PaperOHP transparencies Paper not supported by this printer Printable Area Loading Paper in the Paper Tray Loading PaperLoad paper into the tray with the print side up Specifying paper size using the operation panel Printer SetupSET * Size TRAY1 * SizeOpen the bypass tray Loading Paper in the Bypass TraySlide the side guides Load paper until it stops with the print side downBypass Tray Size Sliding out the Output Tray ExtenderPress Enter until Bypass Tray Size appears Error & Status Messages on the Operation Panel Troubleshooting⇒ P.38 Removing Misfed Pa Tle. ⇒ P.53 Replacing Waste Toner Bottle and Charg Printer Doesnt Print Possible Cause SolutionsTerface cable If the printer is using the I/O timeout settingNetwork Connection Windows NT4.0 Windows 95/98Status Possible Causes, Descriptions, and Solutions Other Printing ProblemsTions for Paper Ing the Charger Removing Misfed Paper Appears When the Message OpenMisfeed Appears Bypass trayTray Appears When the Message RemoveOpen the paper exit cover Remove the misfed paper from Remove the misfed paper from inside of the printerClose the paper exit cover Close the front cover Cleaning the Friction Pad Cleaning the PrinterCleaning the Charger Remove the cleaning brush from back of the front cover Cleaning the Dust-proofing glassTFWX280E Open the left cover Replacing ConsumablesSlide the lock lever up Hold the new toner cartridge Remove the protective sheet from the new toner cartridgeShake it with a horizontal motion About 10 times, as shown in the il- lustrationMagenta Toner MaintenanceMagenta Toner Please Wait Replace Toner MagentaReplacing the Photoconductor Unit Turn off the printers power switchReplace PCU TFWX400E Replacing the Fuser Oil Bottle and Ozone Filter Turn on the printer’s power switchFuser OIL LOW ADD Fuser OIL Close the fuser oil bottle cover Remove the green cap from the new oil bottleInsert a new ozone filter into the printer Replacing the Waste Toner Bottle and Charger Waste Toner Almost FullLocks release, and the charg- er is lifted slightly Moving and Transporting the Printer AppendixMainframe SpecificationsDimensions Noise Emission Sound Power LevelWeight Warm-up TimeOptional Equipment Options Toner Cartridge ConsumablesOther Consumables Service Life *1Index
Top Page Image Contents