Ricoh AP505 manual Replacing the Fuser Oil Bottle and Ozone Filter, Fuser OIL LOW ADD Fuser OIL

Page 68

Troubleshooting

Note

❒Do not close the front cover re- moving the photoconductor unit. Otherwise, you cannot re- place the photoconductor unit because the photoconductor unit holder will be closed. If you do this by mistake, return the photoconductor unit holder to its original position before re- placing the photoconductor unit.

4

TFWX300E

IHold the inset grips (green part) of the new photoconductor unit, and push the photoconductor unit to its original position.

JFix the photoconductor unit with fastening the screws using the screw driver.

KClose the front cover.

Make sure that the front cover close properly.

LTurn on the printer’s power switch.

Replacing the Fuser Oil Bottle and Ozone Filter

HHold the inset grips (green part) of the new photoconductor unit, and insert the photoconductor unit into the photoconductor unit holder.

When inserting the photoconduc- tor unit, be careful not to damage the surface of it.

TFWX305E

Note

❒The white powder on the photo- conductor unit is to protect it af- ter installation into the printer. This white powder doesn't have any adverse effect on the interi- or of the printer.

Replace the oil bottle and ozone filter whenever the message shown below appears on the panel display.

FUSER OIL LOW

ADD FUSER OIL

There is the fuser oil bottle and the ozone filter in the Fuser Oil Type305.

RWARNING:

•Do not incinerate the oil bottle. This action could cause a fire or getting burned.

•Spilt oil is very slippery. If oil is spilt, wipe it with alkaline cleaner. Otherwise, the oily surfaces can create the dan- ger of slipping and personal injury.

50

Image 68

Contents Printer Reference Overseas Affiliates Page Means Power ON. b means Power OFF Page Means Power ON. b means Power OFF Page Means Power ON. b means Power OFF Trademarks Safety Information Safety During OperationIii Page Energy Star Program Low-power mode Energy Save modeSpecifications Manuals for Your Printer Manuals for Your PrinterHow to Read this Manual SymbolsTable of Contents Cleaning the Printer Moving and Transporting the Printer SpecificationsReplacing Consumables ConsumablesPage Guide to the Printer Exterior-Front ViewBypass tray Paper TrayExterior-Rear View Interior Operation Panel Turning the Printer On and Off Turning On the PrinterTurning Off the Printer ReadyInstalling Options Available Options Memory Unit Type505 ⇒ P.9Installing the Memory Unit Type505 Dimm For more information on Installing the Printer Hard Disk Type505 Check the contents of the box for the following itemsPress Enter Press Enter to Initialize DiskInitializing Installing the Paper Feed Unit Type305 Move the printer to make install- ing spaceRemove both pieces of adhesive tape Pull out the paper tray, and re- move the paddingRemove the ring attached to the red tag Place the printer on the paper feed unitPaper and Other Media Supported by this Printer Paper Types and SizesPaper Sizes Metric version B6 JIS⇒ P.27 Loading Paper in the Bypass Tray Paper Sizes Inch version ⇒ P.27 Loading Paper in the Bypass Tray Precautions for Paper Paper types and cautions Plain paperThick Paper Adhesive labelsOHP transparencies Paper not supported by this printer Printable Area Load paper into the tray with the print side up Loading PaperLoading Paper in the Paper Tray Printer Setup Specifying paper size using the operation panelSET * Size TRAY1 * SizeLoading Paper in the Bypass Tray Open the bypass traySlide the side guides Load paper until it stops with the print side downPress Enter until Bypass Tray Size appears Sliding out the Output Tray ExtenderBypass Tray Size Troubleshooting Error & Status Messages on the Operation Panel⇒ P.38 Removing Misfed Pa Tle. ⇒ P.53 Replacing Waste Toner Bottle and Charg Possible Cause Solutions Printer Doesnt PrintNetwork Connection If the printer is using the I/O timeout settingTerface cable Windows 95/98 Windows NT4.0Other Printing Problems Status Possible Causes, Descriptions, and SolutionsTions for Paper Ing the Charger Removing Misfed Paper When the Message Open AppearsMisfeed Appears Bypass trayOpen the paper exit cover When the Message RemoveTray Appears Close the paper exit cover Close the front cover Remove the misfed paper from inside of the printerRemove the misfed paper from Cleaning the Charger Cleaning the PrinterCleaning the Friction Pad Cleaning the Dust-proofing glass Remove the cleaning brush from back of the front coverTFWX280E Slide the lock lever up Replacing ConsumablesOpen the left cover Remove the protective sheet from the new toner cartridge Hold the new toner cartridgeShake it with a horizontal motion About 10 times, as shown in the il- lustrationMaintenance Magenta TonerMagenta Toner Please Wait Replace Toner MagentaReplace PCU Turn off the printers power switchReplacing the Photoconductor Unit TFWX400E Fuser OIL LOW ADD Fuser OIL Turn on the printer’s power switchReplacing the Fuser Oil Bottle and Ozone Filter Remove the green cap from the new oil bottle Close the fuser oil bottle coverInsert a new ozone filter into the printer Waste Toner Almost Full Replacing the Waste Toner Bottle and ChargerLocks release, and the charg- er is lifted slightly Appendix Moving and Transporting the PrinterSpecifications MainframeNoise Emission Sound Power Level DimensionsWeight Warm-up TimeOptional Equipment Options Consumables Toner CartridgeService Life *1 Other ConsumablesIndex