Ricoh AP505 manual OHP transparencies

Page 40

Paper and Other Media

❖OHP transparencies

• When printing on OHP transparency, use the bypass tray.

3

TFWY060E

•Load OHP transparencies into the tray with the print side down. Other- wise, it may stick to the fusing unit and cause a misfeed.

•Remove any unused OHP transparencies from the tray after you are fin- ished printing. Leaving them in the tray can cause them to curl.

•When printing on OHP transparencies, you should select the OHP trans- parency mode with the printer driver.

•The bypass tray can hold up to 50 OHP transparency sheets.

Note

❒The number of sheets to be set may vary depending on the paper thick- ness and paper type.

•When the “OHP SLIP SHEET” setting is set to “NO”, be sure to remove each OHP transparency immediately after it is printed. For more informa- tion, see the “Getting Started”.

Note

❒This printer uses paper in tray 1 for OHP slip sheet even if the direction and size of paper loaded in tray 1 is different from the direction and size of the OHP transparency. Check the direction and size of paper loaded in tray 1 before using “OHP SLIP SHEET” setting.

❒When there is no paper in tray 1, “OHP SLIP SHEET” will not work even if “OHP SLIP SHEET” setting is set to “YES”. Be sure to remove each OHP transparency immediately after it is printed.

22

Image 40

Contents Printer Reference Overseas Affiliates Page Means Power ON. b means Power OFF Page Means Power ON. b means Power OFF Page Means Power ON. b means Power OFF Trademarks Safety Information Safety During OperationIii Page Specifications Low-power mode Energy Save modeEnergy Star Program Manuals for Your Printer Manuals for Your PrinterHow to Read this Manual SymbolsTable of Contents Cleaning the Printer Moving and Transporting the Printer SpecificationsReplacing Consumables ConsumablesPage Guide to the Printer Exterior-Front ViewBypass tray Paper TrayExterior-Rear View Interior Operation Panel Turning the Printer On and Off Turning On the PrinterTurning Off the Printer ReadyInstalling Options Available Options Memory Unit Type505 ⇒ P.9Installing the Memory Unit Type505 Dimm For more information on Installing the Printer Hard Disk Type505 Check the contents of the box for the following itemsInitializing Press Enter to Initialize DiskPress Enter Installing the Paper Feed Unit Type305 Move the printer to make install- ing spaceRemove both pieces of adhesive tape Pull out the paper tray, and re- move the paddingRemove the ring attached to the red tag Place the printer on the paper feed unitPaper and Other Media Supported by this Printer Paper Types and SizesPaper Sizes Metric version B6 JIS⇒ P.27 Loading Paper in the Bypass Tray Paper Sizes Inch version ⇒ P.27 Loading Paper in the Bypass Tray Precautions for Paper Paper types and cautions Plain paperThick Paper Adhesive labelsOHP transparencies Paper not supported by this printer Printable Area Loading Paper in the Paper Tray Loading PaperLoad paper into the tray with the print side up Printer Setup Specifying paper size using the operation panelSET * Size TRAY1 * SizeLoading Paper in the Bypass Tray Open the bypass traySlide the side guides Load paper until it stops with the print side downBypass Tray Size Sliding out the Output Tray ExtenderPress Enter until Bypass Tray Size appears Troubleshooting Error & Status Messages on the Operation Panel⇒ P.38 Removing Misfed Pa Tle. ⇒ P.53 Replacing Waste Toner Bottle and Charg Possible Cause Solutions Printer Doesnt PrintTerface cable If the printer is using the I/O timeout settingNetwork Connection Windows 95/98 Windows NT4.0Other Printing Problems Status Possible Causes, Descriptions, and SolutionsTions for Paper Ing the Charger Removing Misfed Paper When the Message Open AppearsMisfeed Appears Bypass trayTray Appears When the Message RemoveOpen the paper exit cover Remove the misfed paper from Remove the misfed paper from inside of the printerClose the paper exit cover Close the front cover Cleaning the Friction Pad Cleaning the PrinterCleaning the Charger Cleaning the Dust-proofing glass Remove the cleaning brush from back of the front coverTFWX280E Open the left cover Replacing ConsumablesSlide the lock lever up Remove the protective sheet from the new toner cartridge Hold the new toner cartridgeShake it with a horizontal motion About 10 times, as shown in the il- lustrationMaintenance Magenta TonerMagenta Toner Please Wait Replace Toner MagentaReplacing the Photoconductor Unit Turn off the printers power switchReplace PCU TFWX400E Replacing the Fuser Oil Bottle and Ozone Filter Turn on the printer’s power switchFuser OIL LOW ADD Fuser OIL Remove the green cap from the new oil bottle Close the fuser oil bottle coverInsert a new ozone filter into the printer Waste Toner Almost Full Replacing the Waste Toner Bottle and ChargerLocks release, and the charg- er is lifted slightly Appendix Moving and Transporting the PrinterSpecifications MainframeNoise Emission Sound Power Level DimensionsWeight Warm-up TimeOptional Equipment Options Consumables Toner CartridgeService Life *1 Other ConsumablesIndex