Ricoh AP505 manual Sliding out the Output Tray Extender, Bypass Tray Size

Page 46

Paper and Other Media

Specifying paper size using the operation panel

Use the following procedure to speci- fy the paper size from the printer's operation panel after loading paper into the bypass tray.

A Press {Menu}.
3	On Line
3
	Menu	Cancel	Enter
Power	Error	Data In
			TFWS020E
B Use {U}{T} to display “PRINT-
ER SETUP”.

PRINTER SETUP

Sliding out the Output Tray Extender

If you load paper of A4L or 81/2" × 11"L or larger, slide out the output tray extender.

Important

❒Do not place the rear end of the printer near a wall or touch it with barehands. This area can become extremely hot.

TFWX440E

CPress {Enter} until “BYPASS TRAY SIZE” appears.

BYPASS TRAY SIZE

8.5x11 *

DUse {U} {T} to select the paper size you have specified for the pa- per tray, and then press {Enter}.

BYPASS TRAY SIZE 8x13

EPress {Menu}.

The setting becomes effective.

FPress {Menu}.

The normal display screen ap- pears.

READY

Note

❒After printing, return the output tray extender to its original posi- tion.

28

Image 46

Contents Printer Reference Overseas Affiliates Page Means Power ON. b means Power OFF Page Means Power ON. b means Power OFF Page Means Power ON. b means Power OFF Trademarks Safety Information Safety During OperationIii Page Specifications Low-power mode Energy Save modeEnergy Star Program Manuals for Your Printer Manuals for Your PrinterHow to Read this Manual SymbolsTable of Contents Replacing Consumables Cleaning the PrinterMoving and Transporting the Printer Specifications ConsumablesPage Guide to the Printer Exterior-Front ViewBypass tray Paper TrayExterior-Rear View Interior Operation Panel Turning Off the Printer Turning the Printer On and OffTurning On the Printer ReadyInstalling Options Available Options Memory Unit Type505 ⇒ P.9Installing the Memory Unit Type505 Dimm For more information on Installing the Printer Hard Disk Type505 Check the contents of the box for the following itemsInitializing Press Enter to Initialize DiskPress Enter Installing the Paper Feed Unit Type305 Move the printer to make install- ing spaceRemove the ring attached to the red tag Remove both pieces of adhesive tapePull out the paper tray, and re- move the padding Place the printer on the paper feed unitPaper and Other Media Supported by this Printer Paper Types and SizesPaper Sizes Metric version B6 JIS⇒ P.27 Loading Paper in the Bypass Tray Paper Sizes Inch version ⇒ P.27 Loading Paper in the Bypass Tray Precautions for Paper Paper types and cautions Plain paperThick Paper Adhesive labelsOHP transparencies Paper not supported by this printer Printable Area Loading Paper in the Paper Tray Loading PaperLoad paper into the tray with the print side up SET * Size Printer SetupSpecifying paper size using the operation panel TRAY1 * SizeSlide the side guides Loading Paper in the Bypass TrayOpen the bypass tray Load paper until it stops with the print side downBypass Tray Size Sliding out the Output Tray ExtenderPress Enter until Bypass Tray Size appears Troubleshooting Error & Status Messages on the Operation Panel⇒ P.38 Removing Misfed Pa Tle. ⇒ P.53 Replacing Waste Toner Bottle and Charg Possible Cause Solutions Printer Doesnt PrintTerface cable If the printer is using the I/O timeout settingNetwork Connection Windows 95/98 Windows NT4.0Other Printing Problems Status Possible Causes, Descriptions, and SolutionsTions for Paper Ing the Charger Removing Misfed Paper Misfeed Appears When the Message OpenAppears Bypass trayTray Appears When the Message RemoveOpen the paper exit cover Remove the misfed paper from Remove the misfed paper from inside of the printerClose the paper exit cover Close the front cover Cleaning the Friction Pad Cleaning the PrinterCleaning the Charger Cleaning the Dust-proofing glass Remove the cleaning brush from back of the front coverTFWX280E Open the left cover Replacing ConsumablesSlide the lock lever up Shake it with a horizontal motion Remove the protective sheet from the new toner cartridgeHold the new toner cartridge About 10 times, as shown in the il- lustrationMagenta Toner Please Wait MaintenanceMagenta Toner Replace Toner MagentaReplacing the Photoconductor Unit Turn off the printers power switchReplace PCU TFWX400E Replacing the Fuser Oil Bottle and Ozone Filter Turn on the printer’s power switchFuser OIL LOW ADD Fuser OIL Remove the green cap from the new oil bottle Close the fuser oil bottle coverInsert a new ozone filter into the printer Waste Toner Almost Full Replacing the Waste Toner Bottle and ChargerLocks release, and the charg- er is lifted slightly Appendix Moving and Transporting the PrinterSpecifications MainframeWeight Noise Emission Sound Power LevelDimensions Warm-up TimeOptional Equipment Options Consumables Toner CartridgeService Life *1 Other ConsumablesIndex