Panasonic WJ-RT208 manual Master HDD of IDE port HDD connected to IDE port Slave HDD

Page 12

4.Ready the hard disk and install wire jumpers.

To connect two hard disks to one IDE interface, make sure to designate one as the Master HDD and the other the Slave HDD. If only one hard disk is connected, make this the Master HDD. (For connection of the Master and Slave HDD, refer to the operating instructions of the hard disk.)

Pay attention to the following when choosing the connection position of the Master and Slave HDD.

(1)When connecting two hard disks to IDE port 1, make the one on the left the Master and the one on the right the Slave, as seen from the front of the recorder. See Fig. 3.

(2)When connecting three pairs of hard disks to IDE port 0, 2 and 3 (6 in total), make the top one the Master and the bot- tom one the Slave (see Figs. 3 and 5).

Master HDD of IDE port 1

HDD connected to IDE port 0

Slave HDD of

IDE port 1

HDD connected to IDE port 3

HDD connected to IDE port 2

Fig. 3

Note: Port 0 was installed to the two disks installed model. Port 0 and 1 were installed to the four disks installed model. (For the relation between hard disk positions refer to the figure above or the explanation on hard disk management on page 47.)

5.Insert the hard disk into the hard disk fixing frame.

Fix it with four screws at the side of the frame. (Fig. 4, 5)

Master HDD

Slave HDD

Fig. 4

Fig. 5

6.Insert the hard disk fixing frame in the proper location inside the recorder and fix it with a screw (Fig. 6). (Be careful not to damage the fan connection terminal and hard disk cable.)

Fig. 6

Fig. 7

12

Image 12
Contents Operating Instructions Lightning flash with arrowhead symbol Important Safety Instructions Disclaimer of Warranty Limitation of LiabilityPrecautions Trademarks and Registered TrademarksAbout These Operating Instructions Contents Features PrefaceMajor Operating Controls & Their Functions Front View6Cancel Button ESC @6Copy Connector Copy↓ Down button ← Left buttonRear View Installation Installing the Hard DiskPlaces to avoid About mountingMaster HDD of IDE port HDD connected to IDE port Slave HDD Page System Composition and Connections Basic SystemExample for Basic System Connections Basic ConnectionConnection with RS485 Camera WJ-RT208Connection with External HDD For Data Backup Network SystemExample for Network System Connection Direct PC ConnectionConnections with any Existing Network System Connections with a Broadband WAN NetworkUser type When connecting a single unit with a controller When connecting multiple units with a controllerConnection with PS·Data systems When using WJ-SX150 When using WJ-MP204Pin No Signal Operation Remarks RS485 ConnectionDIP Switch Setting Setup Procedures Turning the Power OnPreparation User RegistrationBasic Operation of the Menu Menu type Main menu Submenu ExampleTurning the Power Off 2005-01-28 CancelModification of the System Time Time & Date YYYY-MM-DD HhmmssOperation Screen OperationManual Recording Playback of Recorded ImageOperations for Events Playback the recordEvent type Action at an eventCancellation of alarm PTZ Setup PTZ Select Preset InformationCamera Control RS485 Setup Panning/TiltingAuto function Auto Pan, etc PanasonicTo register preset position of cameras To display the camera setting menuZoom FocusComputer configuration Control this Unit with a PCOutlined functions Setup Setting Item DescriptionOperation for Various Settings System Management System MANNtsc Reboot system Reboot System Picture adjustment Picture AdjustDisk information Disk Information Time & date Time & DateRecording & event setup REC & Event Timer recording Timer RECRecord search Search Terminal recording Terminal RECVideo motion detector recording VMD REC VMD Area Setup Area Setup Time Per File 015 Min CancelSetup enabled range 005 Record length Record LengthPTZ setup PTZ Setup Camera setup Camera SetupPreset position information Preset INFORMA- Tion PTZ selection PTZ SelectCommunication setup Communica Network setup Network SetupTCP RS485 setup RS485 Setup Data port setup Data Port SetupReport Report System log System LOGReport System LOG Event LOG Oldest Data Information User level setup User Level Setup User information User InformationEvent log Event LOG Oldest data information Oldest Data InforPassword Password Do you really want to lock keyboard ? CancelData management Data MANAGE- Ment Online user information Online User INFORMA- TionBackup by External HDD Search and PlaybackChannel No Start End Event Only 2004-10-22 2004-10-27Data Management Factory Default Backup 2004-10-10All data will be deleted Will you continue ? Cancel Disk ManagementHDD formatting Disk FormatReturning the Configuration to the Default Settings Recovery of hard disk indexSystem Screen Explanations Ordinary screen 9-split screenScreen in a certain channel Setup Menu Parameters and Initial Setup Values System Management System ManagementRecording & Event Setup REC & Event Timer Recording Timer RECRecording Search Search Terminal Recording Terminal RECPTZ Setup PTZ Setup Camera Setup Camera Setup Communication Setup Communication SetupNetwork Setup Network Setup RS485 Setup RS485 SetupReport Report System Log System LOGEvent Log Event LOG Oldest Data Information Oldest Data InformationUser Information User Information Data Management Data ManagementOperation using the system controller Operation using the WV-CU650Available only during playback Troubleshooting Problem Check item/remedySpecifications Basic SpecificationsGeneral Input/OutputStandard Accessories Table of Recording LengthPage Ns0306-1046 3TR004320BAA