Extron electronic MKP 2000 user manual Control connections, RS-232 cable termination

Page 12

Installation, cont’d

Control connections

The MKP has two RS-232 ports; a Host port ( 1 ) and a Switcher port ( 2 ); and an Ethernet (LAN) port ( 3 ).

Any number of control panels can be connected, as part of a network, to any Ethernet-enabled matrix switcher via the switcher’s Ethernet port (figure 2-10). All TP cables in this example are wired as patch (straight) cables.

An MKP control panel can be directly connected to any Extron matrix switcher through the switcher’s RS-232 port (figure 2-8). A control system or host computer can be connected via the MKP’s host RS-232 port. Additional MKPs can be connected to the matrix switcher through the MKP that is RS-232 connected to the switcher (the primary MKP). The additional (secondary) MKPs are connected to the primary MKP via the primary MKP’s Ethernet port.

1 2 3

4 5 6

7 8 9

BACK 0

MKP 2000

MKP 2000

MKP 2000

1 2 3

4 5 6

7 8 9

BACK 0

MKP 2000

1 2 3

4 5 6

7 8 9

BACK 0

MKP 2000

MKP 2000

 

Matrix Switcher

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13

14

15

16

17

18

19

20

21

22

23

24

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

2

3

 

1

2

3

4

5

6

7

8

9

10

11

12

4

5

6

 

 

 

 

 

 

 

 

 

 

 

 

4

5

6

Ethernet

 

 

 

 

 

 

 

 

 

 

 

 

1

2

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

8

9

 

 

 

 

 

 

 

 

 

 

 

 

 

BACK 0

 

13

14

15

16

17

18

19

20

21

22

23

24

BACK 0

 

Patch

1

2

3

4

5

6

7

8

9

10

11

12

7

8

9

1

2

3

4

5

6

7

8

9

10

11

12

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13

14

15

16

17

18

19

20

21

22

23

24

 

 

 

1

2

3

4

5

6

7

8

9

10

11

12

 

 

MKP 2000

Cable

 

 

 

 

 

 

 

 

 

 

 

 

MKP 2000

13

14

15

16

17

18

19

20

21

22

23

24

MKP 2000

Matrix Switcher

MKP 2000

1 2 3

4 5 6

7 8 9

BACK 0

MKP 2000

MKP 2000

Ethernet

Ethernet

Switcher

RS-232 Port

1 2 3

4 5 6

7 8 9

BACK 0

MKP 2000

MKP 2000

Host

RS-232 Port

PC

Figure 2-10 — Network MKP connection using the LAN port

1

2

3

4

5

6

7

8

9

BACK

0

 

MKP 2000

 

MKP 2000

Control

 

System

RS-232 cable termination

Each MKP control panel has two RS-232 ports that are connected using 3.5 mm, 3-pole direct insertion connectors. Wire the connectors as follows:

Figure 2-8 — MKP connection using the RS-232 port

An MKP control panel can be directly connected to any Ethernet-enabled matrix switcher via the switcher’s Ethernet port (figure 2-9) using a network (TP) cable that is wired as a crossover cable (see TP cable termination to properly wire the cable).

1

2

3

 

1

2

3

4

5

6

7

8

9

10

11

12

7

8

9

LAN Port

13

14

15

16

17

18

19

20

21

22

23

24

4

5

6

 

 

 

 

 

 

 

 

 

 

 

 

 

BACK 0

 

Crossover

1

2

3

4

5

6

7

8

9

10

11

12

 

 

 

13

14

15

16

17

18

19

20

21

22

23

24

 

 

MKP 2000

Cable

 

 

 

 

 

 

 

 

 

 

 

 

MKP 2000

 

Matrix Switcher

Figure 2-9 — Direct MKP connection using the LAN port

 

 

The total cable length between an MKP control panel

 

 

and a matrix switcher should not exceed 100 feet (30 m).

1.

Choose a cable such as Extron’s Comm-Link cable. The

 

wire specifications for Comm-Link cable are on page A-6.

 

Colors may vary from this example.

2.

Trim approximately 1.5" (3.8 cm) of the cable jacket to

 

expose the four insulated wires and a bare drain wire

 

(silver-colored).

3.

Cut off the foil shield and discard it.

4.

Strip 1/4" ( 0.6 cm) of insulation from three of the four

 

wires.

5.

Twist the strands of each wire, insert them into the direct

 

insertion connector, and tighten the captive screws.

2-10 MKP 2000 Remote Control Panel • Installation

MKP 2000 Remote Control Panel • Installation 2-11

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Remote Control Panel MKPPrecautions Extron’s WarrantyQuick Start Guide MKP Table of Contents MKP 2000 Remote Control Panel Table of Contents, cont’dOne IntroductionAbout the MKP 2000 Remote Control Panel RS-232 connection to the switcherEthernet connection to the switcher MKP 2000 Remote Control Panel IntroductionInstallation TwoInstallation MKP Installation OverviewUL Requirements for Wall Box Installation Installation ProceduresInstallation, cont’d Preparing the site, installing the mud ring or wall boxInstalled in a wall box To meet the UL listing requirements, this device must beMounting the MKP to the mud ring or wall box Detail aSwitch Rear Panel and Side Panel ConnectionsControl connections RS-232 cable termination11 RJ-45 connector and pinout tables TP cable terminationPower supply wiring ThreeLocal Operation MKP 2000 Remote Control Panel Local Operation Local OperationFront Panel Controls and Indications Front Panel OperationsViewing and configuring the IP and MKP set-up parameters Local Operation, cont’dViewing the last input or output tied from the MKP Host control port setting and pass-through communications Input Output TakeRear Panel Resets Control panel security lockout executive modePerforming soft resets Performing a hard reset FourSIS Operation SIS Operation RS-232 LinksEthernet Link Host-to-MKP InstructionsMKP Error Responses Using the Command/Response TableSIS Operation, cont’d Symbol definitions for MKP SIS commands Xxx.xxWhere Command/response table for MKP SIS commands SIS Operation Cont’dMKP Five Html OperationMKP 2000 Remote Control Panel Html Operation Html OperationDownload the Startup System Settings Html Operation, cont’d System StatusIP Settings section Switcher Settings sectionHtml Operation, cont’d Port RS-232 Settings Date/Time Settings fieldsFront panel configuration lock Authorized inputs and authorized outputsHtml Operation, cont’d Passwords Firmware UpgradeFile Management AAppendix a Reference DataHtml Operation, cont’d Special Characters Specifications Reference DataPart Numbers Reference Data, cont’d Mounting and Cabling Specifications Electrical box cutoutPanel mount cutout template Drawn to scale may be used as a templateReference Data, cont’d Extron Comm-Link cable
Top Page Image Contents