Extron electronic MKP 2000 user manual Mounting the MKP to the mud ring or wall box, Detail a

Page 10

Installation, cont’d

7a. If you are using a mud ring, follow the directions, if any, that came with the mud ring to attach the clips that fasten the ring to the wall or furniture (figure 2-3).

To meet the UL listing requirements, this device must be installed in a wall box.

Wall Stud

Wall Box

Sheet Rock

Backing Clip

0.75" #6-32 Screw

Mounting Bracket

Detail A

Sheet Rock

Backing Clip

Screws or Nails

Flush with Wall Surface

1.25" #6-32 Screw

Mounting Bracket

Detail B

Backing Clip can

be in either orientation. See Detail A or Detail B.

R

1

4

7 BACK

2

5

8

0

	3
	6
	9
CA	NC	EL
CA	NC

	TPU	T
OU

INPU	T

TAK	E

	KP	20	00
M	KP

Figure 2-4 — Attaching a wall box to a wall stud

8. Connect the Ethernet and/or RS-232 cable (as appropriate) and the power cable and test the MKP before fastening the MKP into the wall box. See Rear Panel and Side Panel Connections on page 2-8, for details.

Extron

MKP 2000

Figure 2-3 — Attaching a mud ring to a wall

7b. If you are using a wall box, insert the wall box into the opening, and attach it to the wall stud/furniture with nails or screws, leaving the front edge flush with the outer wall or furniture surface (figure 2-4).

If attaching the wall box to wood, use four #8 or #10 screws or 10-penny nails. A minimum of 1/2 inch (1.3 cm) of screw threads must penetrate the wood.

If attaching the wall box to metal studs or furniture, use four #8 or #10 self-tapping sheet metal screws or machine bolts with matching nuts.

The rear panel connectors will be inaccessible after installation.

Mounting the MKP to the mud ring or wall box

1.	Remove power from the control panel by disconnecting
	the power supply.
2.	Place the control panel through the opening in the wall or
	furniture and into the wall box. Take care not to damage
	the cables, which fit behind the MKP, at the back of the
	wall box.

2-6

MKP 2000 Remote Control Panel • Installation

MKP 2000 Remote Control Panel • Installation

2-7

Image 10

Contents Remote Control Panel MKPPrecautions Extron’s WarrantyQuick Start Guide MKP Table of Contents One MKP 2000 Remote Control PanelTable of Contents, cont’d IntroductionEthernet connection to the switcher About the MKP 2000 Remote Control PanelRS-232 connection to the switcher MKP 2000 Remote Control Panel Introduction Installation TwoUL Requirements for Wall Box Installation InstallationMKP Installation Overview Installation ProceduresInstalled in a wall box Installation, cont’dPreparing the site, installing the mud ring or wall box To meet the UL listing requirements, this device must beMounting the MKP to the mud ring or wall box Detail aSwitch Rear Panel and Side Panel ConnectionsControl connections RS-232 cable termination11 RJ-45 connector and pinout tables TP cable terminationThree Power supply wiringLocal Operation Front Panel Controls and Indications MKP 2000 Remote Control Panel Local OperationLocal Operation Front Panel OperationsLocal Operation, cont’d Viewing and configuring the IP and MKP set-up parametersViewing the last input or output tied from the MKP Host control port setting and pass-through communications Input Output TakeControl panel security lockout executive mode Rear Panel ResetsPerforming soft resets Four Performing a hard resetSIS Operation Ethernet Link SIS OperationRS-232 Links Host-to-MKP InstructionsUsing the Command/Response Table MKP Error ResponsesSIS Operation, cont’d Xxx.xx Symbol definitions for MKP SIS commandsWhere Command/response table for MKP SIS commands Cont’d SIS OperationMKP Five Html OperationHtml Operation MKP 2000 Remote Control Panel Html OperationDownload the Startup System Settings Html Operation, cont’d System StatusSwitcher Settings section IP Settings sectionHtml Operation, cont’d Front panel configuration lock Port RS-232 SettingsDate/Time Settings fields Authorized inputs and authorized outputsHtml Operation, cont’d Passwords Firmware UpgradeFile Management Reference Data AAppendix aHtml Operation, cont’d Special Characters Reference Data SpecificationsPart Numbers Panel mount cutout template Reference Data, cont’d Mounting and Cabling SpecificationsElectrical box cutout Drawn to scale may be used as a templateReference Data, cont’d Extron Comm-Link cable