Extron electronic MKP 2000 user manual TP cable termination, 11 RJ-45 connector and pinout tables

Page 13

Installation, cont’d

TP cable termination

It is vital that your Ethernet cables be the correct cables, and that they be properly terminated with the correct pinout. Ethernet links use Category (CAT) 5e or CAT 6, unshielded twisted pair (UTP) or shielded twisted pair (STP) cables, terminated with RJ-45 connectors. Ethernet cables are limited to a length 328' (100 m).

Do not use standard telephone cables. Telephone cables will not support Ethernet or Fast Ethernet.

Do not stretch or bend cables. Transmission errors can occur.

The cable used depends on your network speed. The MKP supports both 10 Mbps (10Base-T — Ethernet) and 100 Mbps

 

 

 

 

 

Patch (straight) cable

 

 

 

 

 

Side 1

 

Side 2

 

 

 

 

Pin

Wire color

Pin

Wire color

 

 

 

 

1

White-orange

1

White-orange

Side Clip Down

 

 

 

 

 

 

2

Orange

2

Orange

1 2 3 4 5 6 7 8

 

Pins

 

 

 

 

 

 

3

White-green

3

White-green

 

 

 

RJ-45

 

 

 

 

 

 

 

 

 

 

 

 

 

connector

4

Blue

4

Blue

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

White-blue

5

White-blue

 

 

 

 

 

 

 

 

 

 

 

 

6

Green

6

Green

 

 

 

 

7

White-brown

7

White-brown

 

 

 

 

 

 

 

 

 

 

 

 

8

Brown

8

Brown

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(100Base-T — Fast Ethernet), half-duplex and full-duplex, Ethernet connections.

10Base-T Ethernet requires CAT 3 UTP or STP cable as a minimum.

100Base-T Fast Ethernet requires CAT 5e UTP or STP cable as a minimum.

The Ethernet cable can be terminated as a straight-through cable or a crossover cable and must be properly terminated for your application (figure 2-11).

Crossover cable — Direct connection between the MKP

and a host computer or an Ethernet-enabled matrix

switcher (figure 2-9).

1 2 3 4 5 6 7 8

1&2

3&6 4&5 7&8

 

 

Crossover cable

 

 

Side 1

 

Side 2

 

Pin

Wire color

Pin

Wire color

 

1

White-orange

1

White-green

Twisted

 

 

 

 

2

Orange

2

Green

Pairs

 

 

 

 

3

White-green

3

White-orange

 

 

 

 

 

 

 

4

Blue

4

Blue

 

 

 

 

 

 

5

White-blue

5

White-blue

 

6

Green

6

Orange

 

 

 

 

 

 

7

White-brown

7

White-brown

 

 

 

 

 

 

8

Brown

8

Brown

Patch (straight) cable — Network connection between

the MKP and an Ethernet LAN (figure 2-10).

Figure 2-11RJ-45 connector and pinout tables

2-12 MKP 2000 Remote Control Panel • Installation

MKP 2000 Remote Control Panel • Installation 2-13

Image 13
Contents MKP Remote Control PanelExtron’s Warranty PrecautionsQuick Start Guide MKP Table of Contents Table of Contents, cont’d MKP 2000 Remote Control PanelOne IntroductionRS-232 connection to the switcher About the MKP 2000 Remote Control PanelEthernet connection to the switcher MKP 2000 Remote Control Panel IntroductionTwo InstallationMKP Installation Overview InstallationUL Requirements for Wall Box Installation Installation ProceduresPreparing the site, installing the mud ring or wall box Installation, cont’dInstalled in a wall box To meet the UL listing requirements, this device must beDetail a Mounting the MKP to the mud ring or wall boxRear Panel and Side Panel Connections SwitchRS-232 cable termination Control connectionsTP cable termination 11 RJ-45 connector and pinout tablesThree Power supply wiringLocal Operation Local Operation MKP 2000 Remote Control Panel Local OperationFront Panel Controls and Indications Front Panel OperationsLocal Operation, cont’d Viewing and configuring the IP and MKP set-up parametersViewing the last input or output tied from the MKP Input Output Take Host control port setting and pass-through communicationsControl panel security lockout executive mode Rear Panel ResetsPerforming soft resets Four Performing a hard resetSIS Operation RS-232 Links SIS OperationEthernet Link Host-to-MKP InstructionsUsing the Command/Response Table MKP Error ResponsesSIS Operation, cont’d Xxx.xx Symbol definitions for MKP SIS commandsWhere Command/response table for MKP SIS commands Cont’d SIS OperationMKP Html Operation FiveHtml Operation MKP 2000 Remote Control Panel Html OperationDownload the Startup Html Operation, cont’d System Status System SettingsSwitcher Settings section IP Settings sectionHtml Operation, cont’d Date/Time Settings fields Port RS-232 SettingsFront panel configuration lock Authorized inputs and authorized outputsFirmware Upgrade Html Operation, cont’d PasswordsFile Management Reference Data AAppendix aHtml Operation, cont’d Special Characters Reference Data SpecificationsPart Numbers Electrical box cutout Reference Data, cont’d Mounting and Cabling SpecificationsPanel mount cutout template Drawn to scale may be used as a templateExtron Comm-Link cable Reference Data, cont’d