Extron electronic MKP 2000 user manual Host control port setting and pass-through communications

Page 17

Local Operation, cont’d

Simultaneously press and hold the buttons for 2 seconds.

Release the buttons.

INPUT OUTPUT

TAKE

The LED display shows the most-significant octet of the MKP 2000’s IP address.

Press the Output button to cycle through the displayed and editable octets.

2.

Use the Input button and Output button to select and

 

display the desired address and octet.

3.

Press the Cancel button to clear the octet to 000.

4.

Use the 0 through 9 buttons to enter the desired value for

 

the octet.

5.

Repeat steps 2 through 4 to select and change other

 

addresses and/or octets.

Press the Input button to cycle through the displayed and editable addresses and to reach the MKP set-up settings.

INPUT

MKP 2000’s

IP Address

INPUT

MKP 2000’s

Subnet Mask

INPUT

MKP 2000’s

Gateway

Address

INPUT

Matrix

Switcher’s

IP Address

INPUT

Host Control

Setting

INPUT

Connection

Priority

OUTPUT OUTPUT OUTPUT OUTPUT

OUTPUT

 

 

1 9 2 . 1.6 8 . 2 5.4

. 2 5 3.

OUTPUT

 

. 0 0 0.

2 5 5 . 2.5 5 . 0 0.0

OUTPUT

 

 

0 0 0 . 0.0 0 . 0 0.0

. 0 0 0.

OUTPUT

 

. 0 0 0.

0 0 0 . 0.0 0 . 0 0.0

Most-significant Octet

Least-significant Octet

(no dot)

(dot in right-most position)

OUTPUT nOPPAS

NoPort

Pass-through Pass-through

OUTPUT OUTPUT

OUTPUT

Pri

 

 

SEC

 

 

Connected to

Control Though

Switcher

Primary (RS-232)

OUTPUT

 

OUTPUT

6.

Use the Input button to select the host control setting

 

display.

7.

If necessary, use the Output button to toggle the setting

 

between pass-through and no pass-through.

8.

Use the Input button to select the connection priority

 

display.

9.

If necessary, use the Output button to toggle the setting

 

between primary and secondary.

10. When all addresses and octets and the host control and priority settings are correct, press the Take button.

Host control port setting and pass-through communications

When the MKP is:

Connected to a computer or control system via its Host RS-232 port and

Is in pass-through mode,

The MKP redirects valid matrix switcher SIS commands that it receives on its Host RS-232 port to its Switcher RS-232 port.

When the MKP is:

Connected to a computer or control system via its Host RS-232 port and

Is in no pass-through mode,

The MKP acts on all valid MKP commands received. It does not pass the command to its Switcher RS-232 port.

When the MKP is:

Figure 3-2 — Selecting octet fields and host control

Selected as primary, it directly controls the matrix switcher via its Switch RS-232 port or LAN port

Selected as secondary,

The MKP controls the matrix switcher through connection to the primary MKP’s IP address

3-6

MKP 2000 Remote Control Panel • Local Operation

MKP 2000 Remote Control Panel • Local Operation

3-7

Image 17
Contents MKP Remote Control PanelExtron’s Warranty PrecautionsQuick Start Guide MKP Table of Contents Table of Contents, cont’d MKP 2000 Remote Control PanelOne IntroductionRS-232 connection to the switcher About the MKP 2000 Remote Control PanelEthernet connection to the switcher MKP 2000 Remote Control Panel IntroductionTwo InstallationMKP Installation Overview InstallationUL Requirements for Wall Box Installation Installation ProceduresPreparing the site, installing the mud ring or wall box Installation, cont’dInstalled in a wall box To meet the UL listing requirements, this device must beDetail a Mounting the MKP to the mud ring or wall boxRear Panel and Side Panel Connections SwitchRS-232 cable termination Control connectionsTP cable termination 11 RJ-45 connector and pinout tablesLocal Operation Power supply wiringThree Local Operation MKP 2000 Remote Control Panel Local OperationFront Panel Controls and Indications Front Panel OperationsViewing the last input or output tied from the MKP Viewing and configuring the IP and MKP set-up parametersLocal Operation, cont’d Input Output Take Host control port setting and pass-through communicationsPerforming soft resets Rear Panel ResetsControl panel security lockout executive mode SIS Operation Performing a hard resetFour RS-232 Links SIS OperationEthernet Link Host-to-MKP InstructionsSIS Operation, cont’d MKP Error ResponsesUsing the Command/Response Table Where Symbol definitions for MKP SIS commandsXxx.xx Command/response table for MKP SIS commands MKP SIS OperationCont’d Html Operation FiveDownload the Startup MKP 2000 Remote Control Panel Html OperationHtml Operation Html Operation, cont’d System Status System SettingsHtml Operation, cont’d IP Settings sectionSwitcher Settings section Date/Time Settings fields Port RS-232 SettingsFront panel configuration lock Authorized inputs and authorized outputsFirmware Upgrade Html Operation, cont’d PasswordsFile Management Html Operation, cont’d Special Characters AAppendix aReference Data Part Numbers SpecificationsReference Data Electrical box cutout Reference Data, cont’d Mounting and Cabling SpecificationsPanel mount cutout template Drawn to scale may be used as a templateExtron Comm-Link cable Reference Data, cont’d