Extron electronic MKP 2000 user manual Html Operation, cont’d Passwords, Firmware Upgrade

Page 30

HTML Operation, cont’d

Passwords Page

Access the Passwords page (figure 5-5) by clicking the Configuration tab and then the Passwords link on the left side of the System Settings page.

System (IP)

Settings

Port Settings

Firmware

Upgrade

Firmware Upgrade Page

The Firmware Upgrade page provides a way to replace the firmware that is coded on the MKP’s control board without taking the MKP out of service, opening the enclosure, and replacing the firmware chip. Access the Firmware Upgrade page (figure 5-6) by clicking the Configuration tab and then the Firmware Upgrade link on the left side of the System Settings page.

System (IP)

Settings

Port Settings

Passwords

Figure 5-5 — Passwords page

The fields on the Passwords page are for entering and verifying administrator and user passwords. Passwords are case sensitive and are limited to 12 uppercase and lowercase alphanumeric characters. Each password must be entered twice; once in the Password field and then again in the Re-enter Password field. Characters in these fields are masked (•••••). If you do not

want to password protect an access level, leave the Password field and the Re-Enter Password field blank. All changes made on the Port Settings must be confirmed by clicking the Submit button. Clicking the Cancel button abandons the changes.

An administrator password must be created before a user password can be created.

To clear an existing password (so that no password is required), enter a space in the Password and Re-enter Password fields and click the Submit button.

When you have connected multiple MKPs to control a switcher through a primary MKP control panel, do not set a user password on the primary MKP.

Figure 5-6 — Firmware Upgrade page

Update the switcher firmware as follows:

 

 

The Firmware Upgrade page is only for replacing the

 

 

firmware that controls all switcher operation. To insert

 

 

your own HTML pages, see File Management Page, on

 

 

page 5-13.

1.

Visit the Extron web site, www.extron.com and select

 

either:

 

• The download tab and then select firmware files

 

• The MKP 2000 product page

2.

Select the latest firmware file for the MKP and download

 

it. Note the folder to which you save the firmware file.

3.

Connect the PC to the MKP via the switcher’s Ethernet

 

port.

4.

Access the MKP using HTML pages.

5.

Click the Configuration tab.

6.

Click the Firmware Upgrade link.

5-10 MKP 2000 Remote Control Panel • HTML Operation

MKP 2000 Remote Control Panel • HTML Operation 5-11

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Remote Control Panel MKPPrecautions Extron’s WarrantyQuick Start Guide MKP Table of Contents One MKP 2000 Remote Control PanelTable of Contents, cont’d IntroductionEthernet connection to the switcher About the MKP 2000 Remote Control PanelRS-232 connection to the switcher MKP 2000 Remote Control Panel IntroductionInstallation TwoUL Requirements for Wall Box Installation InstallationMKP Installation Overview Installation ProceduresInstalled in a wall box Installation, cont’dPreparing the site, installing the mud ring or wall box To meet the UL listing requirements, this device must beMounting the MKP to the mud ring or wall box Detail aSwitch Rear Panel and Side Panel ConnectionsControl connections RS-232 cable termination11 RJ-45 connector and pinout tables TP cable terminationPower supply wiring ThreeLocal Operation Front Panel Controls and Indications MKP 2000 Remote Control Panel Local OperationLocal Operation Front Panel OperationsViewing and configuring the IP and MKP set-up parameters Local Operation, cont’dViewing the last input or output tied from the MKP Host control port setting and pass-through communications Input Output TakeRear Panel Resets Control panel security lockout executive modePerforming soft resets Performing a hard reset FourSIS Operation Ethernet Link SIS OperationRS-232 Links Host-to-MKP InstructionsMKP Error Responses Using the Command/Response TableSIS Operation, cont’d Symbol definitions for MKP SIS commands Xxx.xxWhere Command/response table for MKP SIS commands SIS Operation Cont’dMKP Five Html OperationMKP 2000 Remote Control Panel Html Operation Html OperationDownload the Startup System Settings Html Operation, cont’d System StatusIP Settings section Switcher Settings sectionHtml Operation, cont’d Front panel configuration lock Port RS-232 SettingsDate/Time Settings fields Authorized inputs and authorized outputsHtml Operation, cont’d Passwords Firmware UpgradeFile Management AAppendix a Reference DataHtml Operation, cont’d Special Characters Specifications Reference DataPart Numbers Panel mount cutout template Reference Data, cont’d Mounting and Cabling SpecificationsElectrical box cutout Drawn to scale may be used as a templateReference Data, cont’d Extron Comm-Link cable
Top Page Image Contents