Command/response table for MKP SIS commands
Command | ASCIICommand | Response | Additional description | |
| (host to MKP) | (MKP to host) |
| |
|
|
|
| |
Front panel security lockout (executive mode) |
|
|
| |
|
|
|
|
|
Lock front panel | 1x | Exe1 | Lock front panel. | |
Unlock front panel | 0x | Exe0 | Unlock front panel. | |
|
|
|
|
|
Read front panel lock | x | X1 |
| Read front panel lock: 1 = locked, 0 = unlocked. |
|
|
|
|
|
Pass-through (RS-232 port redirect)
Configure redirect mode | Esc |
| X2 | * | X3 | * | X4 | * | X5 | CD | Cpn | X2 | •Ccd | X3 | , | X4 | , | X5 | Turn redirect mode on. | ||||
Example: |
| 1*2*50*10D*CD | Cpn01•Ccd00002,00050,00000L | ||||||||||||||||||||
Esc | |||||||||||||||||||||||
Disable redirect |
| *0CD | Cpn |
|
| Ccd00000,00000,00000L | |||||||||||||||||
Esc |
| X2 | X2 | ||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
View redirect | Esc |
| X2 | CD | X3 | , | X4 | , | X5 |
| View redirect mode on/off status. | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
View, information, part number, and firmware requests
Information request | I | MKP•2000 | Report model name. |
| |||
Request for part number | N | See Appendix A for part numbers. |
| ||||
|
|
|
|
|
|
|
|
Query firmware version | Q |
| X6 |
|
| Firmware version x.xx. |
|
Query verbose firmware version | 0Q |
|
|
|
| Provide a detailed status of the Ethernet protocol |
|
| X7 |
|
|
| |||
|
|
|
|
|
| firmware, the MKP controller firmware, and any |
|
|
|
|
|
|
| firmware upgrade. The firmware that is running is |
|
|
|
|
|
|
| marked by asterisk (*). A caret (^) indicates that the |
|
|
|
|
|
|
| firmware has a bad checksum or an invalid load. |
|
|
|
|
|
|
| ?.?? indicates that firmware is not loaded. |
|
Response description: | Ethernet protocol firmware version - controller firmware version - updated firmware version |
| |||||
|
|
|
|
|
|
|
|
Query status | S |
| X8 |
|
| Voltage and temperature readings. |
|
|
|
|
|
|
|
|
|
SIS Operation, cont’d
MKP 2000 Remote
Command/response table for MKP SIS commands (continued)
Command | ASCIICommand | Response | Additional description | ||||
| (host to MKP) | (MKP to host) |
| ||||
|
|
|
|
|
|
|
|
Resets |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Absolute reset | Esc | ZQQQ | Zpq | Performs all of the reset functions as the master | |||
|
|
|
|
|
|
| reset, sets the MKP’s IP address to 192.168.254.254, |
|
|
|
|
|
|
| and sets the subnet mask to 255.255.0.0. |
|
|
|
|
|
|
|
|
Verbose mode |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Set verbose mode on | Esc | X9 | CV | Vrb1 | The MKP reports all status changes to the device | ||
|
|
|
|
|
|
| that sent the command. |
Read verbose mode |
| CV |
|
|
|
| |
Esc | X1 |
|
|
| |||
|
|
|
|
|
|
|
|
Read connection’s security level |
| CK |
|
| Password level protection assigned. | ||
Esc | X10 |
| |||||
Control Panel • SIS Operation 4-9
IP setup
Set MKP name
Set MKP name to factory default
Read MKP name
Set time/date
Read time/date
Set GMT offset
Read GMT offset
Esc |
| X11 | CN | Ipn | X11 |
| Assign a name to the MKP. | |||||||||||
| •CN | Ipn• |
|
|
| Reset the MKP’s name to the factory default. | ||||||||||||
Esc | X12 | |||||||||||||||||
| CN |
|
|
|
|
|
|
| Read assigned MKP name ( |
| may be |
| ). | |||||
Esc |
| X11 |
|
|
|
|
| X11 | X12 | |||||||||
|
|
| CT | Ipt |
|
|
|
|
| Set the time and date. | ||||||||
Esc | X13 | X14 | ||||||||||||||||
| CT |
|
|
|
|
| Read the time and date. | |||||||||||
Esc |
| X14 |
|
|
| |||||||||||||
|
|
| CZ | Ipz |
|
| The divider between hours and minutes is a period. | |||||||||||
Esc | X15 | X15 | ||||||||||||||||
| CZ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| |||||||||||
Esc |
| X15 |
|
|
|
|
|
| ||||||||||