Extron electronic MKP 2000 user manual Table of Contents

Page 4

Quick Start Guide — MKP 2000, cont’d

Step 10

Program the control panel with the size of the connected switcher. See System Settings Page in chapter 5, HTML Operation.

Step 11

Use the control panel to select inputs and outputs. See Front Panel Operations in chapter 3, Local Operation.

Table of Contents

Chapter 1 • Introduction	1-1
About the MKP 2000 Remote Control Panel	1-2
RS-232 connection to the switcher	1-3
Ethernet connection to the switcher	1-3
Chapter 2 • Installation	2-1
MKP Installation Overview	2-2
UL Requirements for Wall Box Installation	2-3
Installation Procedures	2-3
Preparing the site, installing the mud ring or wall box	2-4
Mounting the MKP to the mud ring or wall box	2-7
Rear Panel and Side Panel Connections	2-8
Control connections	2-10
RS-232 cable termination	2-11
TP cable termination	2-12
Power supply wiring	2-14
Chapter 3 • Local Operation	3-1
Front Panel Controls and Indications	3-2
Front Panel Operations	3-3
Creating a tie	3-3
Viewing the last input or output tied from the MKP	3-4
Viewing and configuring the IP and MKP
set-up parameters	3-4
Host control port setting and
pass-through communications	3-7
Control panel security lockout (executive mode)	3-8
Rear Panel Resets	3-8
Performing soft resets	3-8
Performing a hard reset	3-10
Chapter 4 • SIS Operation	4-1
RS-232 Links	4-2
Routing matrix switcher commands	4-2
Ethernet Link	4-3
Default IP address	4-3
Host-to-MKP Instructions	4-3
MKP-Initiated (Unsolicited) Messages	4-3
MKP Error Responses	4-4
Using the Command/Response Table	4-4

QS-2 MKP 2000 Remote Control Panel • Quick Start Guide

MKP 2000 Remote Control Panel• Table of Contents

i

Image 4

Contents Remote Control Panel MKPPrecautions Extron’s WarrantyQuick Start Guide MKP Table of Contents MKP 2000 Remote Control Panel Table of Contents, cont’dOne IntroductionAbout the MKP 2000 Remote Control Panel RS-232 connection to the switcherEthernet connection to the switcher MKP 2000 Remote Control Panel IntroductionInstallation TwoInstallation MKP Installation OverviewUL Requirements for Wall Box Installation Installation ProceduresInstallation, cont’d Preparing the site, installing the mud ring or wall boxInstalled in a wall box To meet the UL listing requirements, this device must beMounting the MKP to the mud ring or wall box Detail aSwitch Rear Panel and Side Panel ConnectionsControl connections RS-232 cable termination11 RJ-45 connector and pinout tables TP cable terminationThree Power supply wiringLocal Operation MKP 2000 Remote Control Panel Local Operation Local OperationFront Panel Controls and Indications Front Panel OperationsLocal Operation, cont’d Viewing and configuring the IP and MKP set-up parametersViewing the last input or output tied from the MKP Host control port setting and pass-through communications Input Output TakeControl panel security lockout executive mode Rear Panel ResetsPerforming soft resets Four Performing a hard resetSIS Operation SIS Operation RS-232 LinksEthernet Link Host-to-MKP InstructionsUsing the Command/Response Table MKP Error ResponsesSIS Operation, cont’d Xxx.xx Symbol definitions for MKP SIS commandsWhere Command/response table for MKP SIS commands Cont’d SIS OperationMKP Five Html OperationHtml Operation MKP 2000 Remote Control Panel Html OperationDownload the Startup System Settings Html Operation, cont’d System StatusSwitcher Settings section IP Settings sectionHtml Operation, cont’d Port RS-232 Settings Date/Time Settings fieldsFront panel configuration lock Authorized inputs and authorized outputsHtml Operation, cont’d Passwords Firmware UpgradeFile Management Reference Data AAppendix aHtml Operation, cont’d Special Characters Reference Data SpecificationsPart Numbers Reference Data, cont’d Mounting and Cabling Specifications Electrical box cutoutPanel mount cutout template Drawn to scale may be used as a templateReference Data, cont’d Extron Comm-Link cable