Ingersoll-Rand ETA2 manual To Store Data by Round ETA5 only

Page 27

7529_eng.fm Page 26 Wednesday, November 12, 2003 8:57 AM

To Store Data by Round - ETA5 ONLY

At main menu, press	3	(Store)
Press	2	(Round)
Screen will show “Select Round No”
Select round number using		and press Enter

The maximum number of rounds that can be stored is 25.

If you are using an Ingersoll-Rand TRD, TSD or Crane UTA type transducer and it is already plugged in, you are now ready to take readings. The job that appears on screen will be the job that you selected to be first when you set up the round.

If you are using any other type of transducer or it is not yet plugged in, you will be prompted to

insert transducer and select transducer to be used. Plug in the transducer and press Enter

When a complete subgroup of readings has been taken for all jobs in the round, screen will

show “Next Round Cycle “. To continue taking readings, press (this message will be repeated at the end of each complete subgroup Sub1, Sub2, etc.)

When you have finished taking all readings, pressing will result in a message that the

round is complete. Press MENU .

To return to the main menu, press MENU MENU

Note: You can erase the last reading taken by pressing Reset .

If you have selected Horizontal sampling and the ETA5 has already switched to the next job, it will switch back when you

press Reset .

It is not possible to erase any readings other than the last one taken in Horizontal sampling mode.

26

Image 27

Contents Operators Manual Operators Manual for Model ETA2 and ETA5 Analyzers Placing Analyzer in Service 7529eng.fm Page 3 Wednesday, November 12, 2003 857 AM Save These INSTRUCTIONS. do not Destroy Table of Contents 7529eng.fm Page 6 Wednesday, November 12, 2003 857 AM Following method is adopted throughout this manual How to use this ManualPacking List Care and Storage Battery ChargingEdit Transducer File For ETA2For ETA5 If you have chosen I/S If you have selected H/O If you have selected KEY Barcode read input for characteristic Names and commentsMeasure Mode Up to 200 readings stored Type in amount of Dip press Measure Mode Circle-Store Option Printing of stored readings from measure modeTo select this option From main menu Press Direct Direct Measure Setup 7529eng.fm Page 18 Wednesday, November 12, 2003 857 AM To set up a Characteristic ETA5 only Select Frequency Response using Then press Enter Through the available characteristics and press Direct Characteristic Mode ETA5 only7529eng.fm Page 22 Wednesday, November 12, 2003 857 AM To Store Data single characteristic ETA5 only 7529eng.fm Page 24 Wednesday, November 12, 2003 857 AM Screen will show Characteristic No 2 of ? To set up a Round ETA5 onlyTo Store Data by Round ETA5 only Set-up To set up a Master Round ETA5 onlyIf you have Next job, it will switch back when you pressTo Store Data by Master Round To return to the main menu, press Menu MenuTo Display Recorded Data on ETA5 To Display Recorded Data on ETA2To View Cp and Cpk To set this function To Erase Readings Stored in Measure ModeFrench Cp and Cpk To Erase Stored DataTo Erase Stored Data and Setups on ETA5 To Erase Characteristic SetupTo Erase Characteristic Data To Erase Round Data To Erase Round Setup InformationPrinting To print details of Setup or Analysis of Data from ETA5To print details of readings by round To print details of all characteristic setups To print details of setup and analysis of readings by roundTo print readings taken by characteristic To print details of a particular round setupThen press Print Measure To Set Date and Time Printing Data to PCTo Configure Printer Port To Set Power Off and Backlight Time DelaysTo Set Password Protection To Display Software Version NumberDisplay window Pressing Will remove the protection Screen will say Confirm password To Clear Password ProtectionTo Perform Software Reset Cm min samples To Communicate with a PC using PC Comms SoftwareExample Printout of Readings taken in Measure Mode Printout of Setup and Readings taken by Characteristic Printout of Analysis by Characteristic Printout of details of all Characteristic setups Printout of Round setup Printout of Readings taken by Characteristic Rotary and Stationary Joint Kits Deg/lbft Lbft Nominal Joint StiffnessesDwg. TPA1919 Callout Description Joint Kit Number Parts ListNot PicturedCharacteristic Glossary of TermsCpK Max Torque Value High Output Transducer H/OHorizontal Sampling Industry Standard Transducer I/SThreshold Torque Value Units of MeasureVertical Plus Prompt Code Message Explanation Error MessagesINCOR-TX OP Code ERR Dwg. TPA1822 External Connections7529eng.fm Page 62 Wednesday, November 12, 2003 857 AM 7529eng.fm Page 63 Wednesday, November 12, 2003 857 AM 7529eng.fm Page 64 Wednesday, November 12, 2003 857 AM 0102