Ingersoll-Rand manual To Display Recorded Data on ETA2, To Display Recorded Data on ETA5

Page 30

7529_eng.fm Page 29 Wednesday, November 12, 2003 8:57 AM

To Display Recorded Data on ETA2

From main menu, press 9 (Display/Analyze)

Screen will show job name and Specs; press

Screen will now show x-bar, R, and sigma for total readings

From any Subgroup display, press

Screen will show the Date and Time the readings for that subgroup were taken.

Press	, screen will show subgroup comment.
Press	again to see the individual readings displayed in groups of four readings per screen.

To Display Recorded Data on ETA5

From main menu, press 9 (Display/Analyze)

Press Enter to display the last recorded Characteristic

Select the job that you want to see using

and press Enter

Screen will show job name and Specs; press

Screen will now show x-bar, R, and sigma for Sub1; press

Screen will now show same information for Sub2

You can use to go back and forth between subgroups as required From any Subgroup display, press

Screen will show the Date and Time the readings for that subgroup were taken.

Press

, screen will show subgroup comment.

29

Image 30

Contents Operators Manual Operators Manual for Model ETA2 and ETA5 Analyzers Placing Analyzer in Service 7529eng.fm Page 3 Wednesday, November 12, 2003 857 AM Save These INSTRUCTIONS. do not Destroy Table of Contents 7529eng.fm Page 6 Wednesday, November 12, 2003 857 AM How to use this Manual Following method is adopted throughout this manualPacking List Battery Charging Care and StorageEdit Transducer File For ETA2For ETA5 If you have chosen I/S If you have selected H/O Barcode read input for characteristic Names and comments If you have selected KEYMeasure Mode Up to 200 readings stored Type in amount of Dip press Measure Mode Circle-Store Option Printing of stored readings from measure modeTo select this option From main menu Press Direct Direct Measure Setup 7529eng.fm Page 18 Wednesday, November 12, 2003 857 AM To set up a Characteristic ETA5 only Select Frequency Response using Then press Enter Direct Characteristic Mode ETA5 only Through the available characteristics and press7529eng.fm Page 22 Wednesday, November 12, 2003 857 AM To Store Data single characteristic ETA5 only 7529eng.fm Page 24 Wednesday, November 12, 2003 857 AM To set up a Round ETA5 only Screen will show Characteristic No 2 of ?To Store Data by Round ETA5 only To set up a Master Round ETA5 only Set-upTo return to the main menu, press Menu Menu Next job, it will switch back when you pressTo Store Data by Master Round If you haveTo Display Recorded Data on ETA2 To Display Recorded Data on ETA5To View Cp and Cpk To Erase Stored Data To Erase Readings Stored in Measure ModeFrench Cp and Cpk To set this functionTo Erase Stored Data and Setups on ETA5 To Erase Characteristic SetupTo Erase Characteristic Data To Erase Round Setup Information To Erase Round DataTo print details of Setup or Analysis of Data from ETA5 PrintingTo print details of readings by round To print details of setup and analysis of readings by round To print details of all characteristic setupsTo print details of a particular round setup To print readings taken by characteristicThen press Print Measure Printing Data to PC To Set Date and TimeTo Set Power Off and Backlight Time Delays To Configure Printer PortTo Set Password Protection To Display Software Version NumberDisplay window Pressing Will remove the protection To Clear Password Protection Screen will say Confirm passwordTo Perform Software Reset To Communicate with a PC using PC Comms Software Cm min samplesExample Printout of Readings taken in Measure Mode Printout of Setup and Readings taken by Characteristic Printout of Analysis by Characteristic Printout of details of all Characteristic setups Printout of Round setup Printout of Readings taken by Characteristic Rotary and Stationary Joint Kits Nominal Joint Stiffnesses Deg/lbft LbftDwg. TPA1919 Pictured Parts ListNot Callout Description Joint Kit NumberCharacteristic Glossary of TermsCpK Industry Standard Transducer I/S High Output Transducer H/OHorizontal Sampling Max Torque ValueThreshold Torque Value Units of MeasureVertical Plus Prompt Error Messages Code Message ExplanationINCOR-TX OP Code ERR External Connections Dwg. TPA18227529eng.fm Page 62 Wednesday, November 12, 2003 857 AM 7529eng.fm Page 63 Wednesday, November 12, 2003 857 AM 7529eng.fm Page 64 Wednesday, November 12, 2003 857 AM 0102