Ingersoll-Rand ETA2, ETA5 manual To Clear Password Protection, Screen will say Confirm password

Page 43

7529_eng.fm Page 42 Wednesday, November 12, 2003 8:57 AM

Press MENU to exit
Display now reads “End of setup”
To return to main menu press MENU or press	to edit password protection

The remaining options can be password protected in the same manner.

To Clear Password Protection

From main menu:

Press then press

Press then press

6(Misc)

5(Password)

Screen will prompt “Password” - - - - enter the existing password (4 characters) and

press Enter

Screen will prompt “Confirm Password” and display the existing password

Press	Enter	to confirm or press Reset to clear the password protection
Screen will prompt “Enter new Password”
Press	Enter	to clear the password (keying in 4 characters before pressing Enter

will result in a new password being created)

Screen will say “Confirm password”

Press Enter to confirm and password is cleared

Notes on Password Protection:

Be aware of the implications of password protection. Always keep a note of the chosen password somewhere safe. As there is no function to enable an existing password to be removed without it first being entered, it may be advisable for the person who is ultimately responsible for the ETA to initially set a password and issue it only to personnel who need the information. This will prevent an unknown password being entered, accidentally or deliberately, without anyone else’s knowledge. If an unknown password is encountered, please contact Ingersoll-Rand for advice.

42

Image 43

Contents Operators Manual Operators Manual for Model ETA2 and ETA5 Analyzers Placing Analyzer in Service 7529eng.fm Page 3 Wednesday, November 12, 2003 857 AM Save These INSTRUCTIONS. do not Destroy Table of Contents 7529eng.fm Page 6 Wednesday, November 12, 2003 857 AM Following method is adopted throughout this manual How to use this ManualPacking List Care and Storage Battery ChargingFor ETA2 Edit Transducer FileFor ETA5 If you have chosen I/S If you have selected H/O If you have selected KEY Barcode read input for characteristic Names and commentsMeasure Mode Up to 200 readings stored Type in amount of Dip press Printing of stored readings from measure mode Measure Mode Circle-Store OptionTo select this option From main menu Press Direct Direct Measure Setup 7529eng.fm Page 18 Wednesday, November 12, 2003 857 AM To set up a Characteristic ETA5 only Select Frequency Response using Then press Enter Through the available characteristics and press Direct Characteristic Mode ETA5 only7529eng.fm Page 22 Wednesday, November 12, 2003 857 AM To Store Data single characteristic ETA5 only 7529eng.fm Page 24 Wednesday, November 12, 2003 857 AM Screen will show Characteristic No 2 of ? To set up a Round ETA5 onlyTo Store Data by Round ETA5 only Set-up To set up a Master Round ETA5 onlyIf you have Next job, it will switch back when you pressTo Store Data by Master Round To return to the main menu, press Menu MenuTo Display Recorded Data on ETA5 To Display Recorded Data on ETA2To View Cp and Cpk To set this function To Erase Readings Stored in Measure ModeFrench Cp and Cpk To Erase Stored DataTo Erase Characteristic Setup To Erase Stored Data and Setups on ETA5To Erase Characteristic Data To Erase Round Data To Erase Round Setup InformationPrinting To print details of Setup or Analysis of Data from ETA5To print details of readings by round To print details of all characteristic setups To print details of setup and analysis of readings by roundTo print readings taken by characteristic To print details of a particular round setupThen press Print Measure To Set Date and Time Printing Data to PCTo Configure Printer Port To Set Power Off and Backlight Time DelaysTo Display Software Version Number To Set Password ProtectionDisplay window Pressing Will remove the protection Screen will say Confirm password To Clear Password ProtectionTo Perform Software Reset Cm min samples To Communicate with a PC using PC Comms SoftwareExample Printout of Readings taken in Measure Mode Printout of Setup and Readings taken by Characteristic Printout of Analysis by Characteristic Printout of details of all Characteristic setups Printout of Round setup Printout of Readings taken by Characteristic Rotary and Stationary Joint Kits Deg/lbft Lbft Nominal Joint StiffnessesDwg. TPA1919 Callout Description Joint Kit Number Parts ListNot PicturedGlossary of Terms CharacteristicCpK Max Torque Value High Output Transducer H/OHorizontal Sampling Industry Standard Transducer I/SUnits of Measure Threshold Torque ValueVertical Plus Prompt Code Message Explanation Error MessagesINCOR-TX OP Code ERR Dwg. TPA1822 External Connections7529eng.fm Page 62 Wednesday, November 12, 2003 857 AM 7529eng.fm Page 63 Wednesday, November 12, 2003 857 AM 7529eng.fm Page 64 Wednesday, November 12, 2003 857 AM 0102