Ingersoll-Rand ETA2, ETA5 manual OP Code ERR

Page 61

7529_eng.fm Page 60 Wednesday, November 12, 2003 8:57 AM

Code	Message	Explanation
803	OP CODE ERR	The processor has attempted to execute an
		illegal instruction.
804	STACK ERR	The processor stack has overflowed.
901	TX SPEC	Illegal transducer specification number received
		from PC.
902	TX TYPE	Illegal transducer type received from PC.
904	TX UNITS	Illegal transducer units data received from PC.
905	SERIAL	Illegal serial transducer data received from PC.
906	UNITS	Illegal units of measure data received from PC.
907	DIRECT	Illegal direction data received from PC.
908	NAME	Name sent from PC is too long.
909	RANGE	Numeric Parameter sent from PC is out of range.
920	RS232	Error receiving RS232 data from PC.
921	TIMEOUT	Timed out receiving message from PC.
922	CRC	Message received from PC has incorrect CRC
		value.
923	ILL MSG	Illegal message received from PC.

NOTE: If ETA can be switched on, but fails to respond to the keyboard, the electronic circuitry may be reset by linking pins 5 and 6 in the PC connector, with a length of wire. This will turn the unit off. Turn the unit on again by pressing ‘ON’. If after this reset ETA still fails to operate correctly, use ‘6’ for Miscellaneous and ‘6’ Software Reset to clear memory. Having carried out a hardware reset as described above the message ‘800 MEMORY’ may be displayed on the next power up, and a software reset should be carried out.

60

Image 61

Contents Operators Manual Operators Manual for Model ETA2 and ETA5 Analyzers Placing Analyzer in Service 7529eng.fm Page 3 Wednesday, November 12, 2003 857 AM Save These INSTRUCTIONS. do not Destroy Table of Contents 7529eng.fm Page 6 Wednesday, November 12, 2003 857 AM Following method is adopted throughout this manual How to use this ManualPacking List Care and Storage Battery ChargingFor ETA2 Edit Transducer FileFor ETA5 If you have chosen I/S If you have selected H/O If you have selected KEY Barcode read input for characteristic Names and commentsMeasure Mode Up to 200 readings stored Type in amount of Dip press Printing of stored readings from measure mode Measure Mode Circle-Store OptionTo select this option From main menu Press Direct Direct Measure Setup 7529eng.fm Page 18 Wednesday, November 12, 2003 857 AM To set up a Characteristic ETA5 only Select Frequency Response using Then press Enter Through the available characteristics and press Direct Characteristic Mode ETA5 only7529eng.fm Page 22 Wednesday, November 12, 2003 857 AM To Store Data single characteristic ETA5 only 7529eng.fm Page 24 Wednesday, November 12, 2003 857 AM Screen will show Characteristic No 2 of ? To set up a Round ETA5 onlyTo Store Data by Round ETA5 only Set-up To set up a Master Round ETA5 onlyTo Store Data by Master Round Next job, it will switch back when you pressTo return to the main menu, press Menu Menu If you haveTo Display Recorded Data on ETA5 To Display Recorded Data on ETA2To View Cp and Cpk French Cp and Cpk To Erase Readings Stored in Measure ModeTo Erase Stored Data To set this functionTo Erase Characteristic Setup To Erase Stored Data and Setups on ETA5To Erase Characteristic Data To Erase Round Data To Erase Round Setup InformationPrinting To print details of Setup or Analysis of Data from ETA5To print details of readings by round To print details of all characteristic setups To print details of setup and analysis of readings by roundTo print readings taken by characteristic To print details of a particular round setupThen press Print Measure To Set Date and Time Printing Data to PCTo Configure Printer Port To Set Power Off and Backlight Time DelaysTo Display Software Version Number To Set Password ProtectionDisplay window Pressing Will remove the protection Screen will say Confirm password To Clear Password ProtectionTo Perform Software Reset Cm min samples To Communicate with a PC using PC Comms SoftwareExample Printout of Readings taken in Measure Mode Printout of Setup and Readings taken by Characteristic Printout of Analysis by Characteristic Printout of details of all Characteristic setups Printout of Round setup Printout of Readings taken by Characteristic Rotary and Stationary Joint Kits Deg/lbft Lbft Nominal Joint StiffnessesDwg. TPA1919 Not Parts ListPictured Callout Description Joint Kit NumberGlossary of Terms CharacteristicCpK Horizontal Sampling High Output Transducer H/OIndustry Standard Transducer I/S Max Torque ValueUnits of Measure Threshold Torque ValueVertical Plus Prompt Code Message Explanation Error MessagesINCOR-TX OP Code ERR Dwg. TPA1822 External Connections7529eng.fm Page 62 Wednesday, November 12, 2003 857 AM 7529eng.fm Page 63 Wednesday, November 12, 2003 857 AM 7529eng.fm Page 64 Wednesday, November 12, 2003 857 AM 0102