Panasonic PT-D4000U manual Projection schemes, Installation geometry

Page 16

Installation

Projection schemes

Any of the following four projection schemes can be used depending on user’s needs or viewing conditions. Use “OPTION2” menu (chosen from the MAIN MENU) to choose the appropriate projection scheme. (page 34)

FLOOR

CEILING

FRONT

 

(Default position)

 

REAR

 

Installation geometry

When planning the projector and screen geometry, refer to the figure below and the information on the next page for reference. After the projector is roughly positioned, picture size and vertical picture positioning can be finely adjusted with the powered zoom lens and lens tilt mechanism.

Side view

Top view

unit : mm, ( ) : inch

With optional ceiling mount bracket (ET-PKD56H)

H

L

SH

H

Screen

 

417-497

(16.4-19.6)

185

256

 

(7.3)

(10.1)

 

SW

 

L

 

200

(7.9)

 

 

 

 

 

 

(3.9)

 

 

 

100 (3.9)

100

 

 

 

 

 

Screen

 

 

200 (7.9)

 

 

 

 

 

L: Projection distance SH : Image height

SW : Image width

H : Distance from center of lens to bottom edge of projected image.

Attention • Do not place or use one projector on top of another projection unit.

Leave a clearance of at least 50 cm (19.7") so that the ventilation opening on the rear panel will not be blocked. (page 59)

16

Image 16
Contents Operating Instructions Commercial UseImportant Safety Notice Dear Panasonic CustomerPage Contents Precautions with regard to safety Remove empty batteries from the remote control at once Do not use or handle the batteries improperlyDo not disassemble the lamp unit Always disconnect all cables before moving the projectorDo not use the old lamp unit AccessoriesDo not place the projector in extremely hot locations Precautions on handling Remote control Name and function of partsBottom Front and side of the projector Status LED lightsRear view of the main unit Controls on rear panel Side-mounted connection terminals Effective range of remote control operation Using the remote control unitLoading dry cells Setting projector ID number to remote control Connect to the projector to use with a cableInstallation geometry InstallationProjection schemes Projection distance by projection lens Screen aspect ratioInstallation Calculation formulas for projection distance by lens types Setup precautions ConnectionExample of connecting with AV products Example of connecting with PCsPowering up the projector Making adjustment and selectionPress the I button. on the main unit or the remote control ProjectionPowering off the projector Direct power off functionHow to adjust the FOCUS, Zoom and Shift How to adjust the lensHow to remove the projection lens Automatic adjustment Press the Status button on the remote controlStatus function Press the Shutter button againOn-screen menus Structure of menu screensMenu items setting Resetting to the factory defaultBasic menu operations Returning to the previousAdjusting the picture Adjusting the position Clock Phase ZoomKeystone Digital Cinema RealityInput Resolution XGA ModeSxga Mode Clamp PositionOPTION1 settings DVI Signal Level DVI EdidFUNC1 OSD PositionOPTION2 settings InstallationProjector ID AltitudeLamp Relay Lamp SelectRS-232C Auto Power OFF PasswordSystem Information Date and TimeSetting the network Connecting the PCSystem requirements Connection exampleUsing Web Browser Control Accessing from the Web browserPassword change Click OKBasic control Change password buttonDetail control Monitor information Error informationOK Normal operation Failed Occurrence of trouble Mail set up When Failed has appeared for an item Parameter DescriptionMail set up page Continuing DNS server set up Authentication server set upPing test Contents of mail sent Adjust clockNetwork config Network statusUsing the PJLink protocol Supported commandsPJLink security authentication Command Control Description RemarksSetting the security Password ChangeDisplay Setting Control Device SetupUsing the serial terminals Pin assignments and signal namesCommunication conditions Factory setting Examples of connectionControl commands Cable specificationsConnecting to a PC Computer Projector DTE specifications Pin assignments and controlIndication of lamp monitor Cleaning and replacement of air filter Procedure of cleaningClean the air filter Dismantle the air filterWhen to replace the Lamp unit Replacing the lamp unitLamp AfterLamp unit replacement steps Remove the two screws securing the fan unitLamp unit will be hot after it has been used Have a Phillips screwdriver ready ahead of timeCeiling Mount Bracket Safeguards Installation procedurePower does Not turn onNo image Image is blurredSpecifications PT-D4000ULength of power cord Cabinet Outside dimensionsRemote control Power source Replacement lamp unitCompatible Signal List PAL-M/PAL60 PAL/PAL-N/SECAMDimensions Installation dimensions diagramTrademark Acknowledgement Concernant LA Sécurité Précautions concernant la sécurité Ne pas surcharger la prise de courantNe jamais tenter de modifier ou de démonter le projecteur Ne pas mettre d’objets étrangers dans le projecteurPendant un orage, ne pas toucher le projecteur ou le câble Ne jamais démonter la lampeNe pas empêcher la chaleur de s’échapper Ne pas utiliser la lampe uséeNettoyage et maintenance Précautions pour la manipulationMise au rebut Précautions pour l’utilisationRemplacement de la lampe Moment adéquat pour remplacer la lampeLampe AprèsLa lampe est chaude si elle vient d’être utilisée Procédure de remplacement de la lampePréparez un tournevis Phillips à l’avance Technical Support Panasonic Projector Systems CompanyPanasonic Canada Inc