Panasonic PT-D4000U manual Lamp Select, Lamp Relay, RS-232C

Page 35

LAMP SELECT

“LAMP SELECT” is used to choose from “SINGLE” and “DUAL” modes depending on user’s needs or viewing conditions.

In “SINGLE” mode, the projector may automatically select either lamp from the 2 lamps, or the particular lamp can be specified.

DUAL : Two lamps are used simultaneously.

SINGLE : One of either lamps is used (lamp with shorter operating hours is automatically selected).

LAMP1 : Lamp Unit 1 is always used.

LAMP2 : Lamp Unit 2 is always used.

When one of the above settings is selected, it will take effect after the ENTER button is pressed.

Note • If, in the “SINGLE”, “LAMP1” or “LAMP2” mode, one lamp remains off

or the currently active lamp exceeds 3 000 hours of cumulative operating time, the other lamp will light. If, in the “DUAL” mode, one lamp remains off or the currently active lamp exceeds

3 000 hours of cumulative operating time, the other lamp alone will light. However, if both lamps remain off or the 3 000 hours of cumulative operating time are exceeded, the projector will enter the standby mode.

•The colors of the items indicate the status.

Green Current setting

Yellow Current setting (when a lamp fails or fails to light)

Red

 

Lamp that has failed to

 

 

 

light

White

 

Any other status

 

•If the projector is repeatedly used for short periods of time, the lamps will need to be replaced more frequently.

LAMP RELAY

If using the projector for a continuous period of 24 hours or more, this setting can be used to automatically switch the lamps that are turned on in order to reduce the lamp deterioration that can occur as a result of continuous use.

OFF : This is the standard setting. “LAMP RELAY” is disabled.

00:00 - 23:00

:This can be set in one hour intervals from 00:00 to 23:00.

Note • Only when “DUAL” or “SINGLE” is selected in “LAMP SELECT”, “LAMP

RELAY” is active. If “LAMP1” or

“LAMP2” is selected, “LAMP RELAY” function is not available.

•When “DUAL” is selected in “LAMP SELECT”, only one lamp will light for a 4-hour period after the set time.

•When “SINGLE” is selected in “LAMP SELECT”, the lamp that was off at the set time will light, and then the lamp that was lighted until the set time will turn off.

•The setting time will be the local time. (page 36)

RS-232C

This sets the communication parameters at the serial terminals.

For details on the serial terminals, refer to “Using the serial terminals” (page 48).

(IN) BAUDRATE

: 9600, 19200 or 38400 is

 

selected.

(IN) PARITY

: NONE, EVEN or ODD is

 

selected.

(OUT) BAUDRATE: 9600, 19200 or 38400 is

 

selected.

(OUT) PARITY

: NONE, EVEN or ODD is

 

selected.

VPS SYSTEM

: MASTER or SLAVE is

 

selected.

GROUP

: A to Z is selected. MASTER

 

or SLAVE is also selected.

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Commercial Use Operating InstructionsDear Panasonic Customer Important Safety NoticePage Contents Precautions with regard to safety Always disconnect all cables before moving the projector Remove empty batteries from the remote control at onceDo not use or handle the batteries improperly Do not disassemble the lamp unitDo not place the projector in extremely hot locations AccessoriesDo not use the old lamp unit Precautions on handling Name and function of parts Remote controlBottom Status LED lights Front and side of the projectorRear view of the main unit Controls on rear panel Side-mounted connection terminals Loading dry cells Using the remote control unitEffective range of remote control operation Connect to the projector to use with a cable Setting projector ID number to remote controlProjection schemes InstallationInstallation geometry Screen aspect ratio Projection distance by projection lensInstallation Calculation formulas for projection distance by lens types Connection Setup precautionsExample of connecting with PCs Example of connecting with AV productsProjection Powering up the projectorMaking adjustment and selection Press the I button. on the main unit or the remote controlDirect power off function Powering off the projectorHow to remove the projection lens How to adjust the lensHow to adjust the FOCUS, Zoom and Shift Press the Shutter button again Automatic adjustmentPress the Status button on the remote control Status functionStructure of menu screens On-screen menusReturning to the previous Menu items settingResetting to the factory default Basic menu operationsAdjusting the picture Adjusting the position Digital Cinema Reality Clock PhaseZoom KeystoneClamp Position Input ResolutionXGA Mode Sxga Mode OPTION1 settings OSD Position DVI Signal LevelDVI Edid FUNC1Altitude OPTION2 settingsInstallation Projector IDRS-232C Lamp SelectLamp Relay Date and Time Auto Power OFFPassword System InformationConnection example Setting the networkConnecting the PC System requirementsClick OK Using Web Browser ControlAccessing from the Web browser Password changeDetail control Change password buttonBasic control OK Normal operation Failed Occurrence of trouble Error informationMonitor information When Failed has appeared for an item Parameter Description Mail set upMail set up page Continuing Ping test Authentication server set upDNS server set up Adjust clock Contents of mail sentNetwork status Network configCommand Control Description Remarks Using the PJLink protocolSupported commands PJLink security authenticationControl Device Setup Setting the securityPassword Change Display SettingExamples of connection Using the serial terminalsPin assignments and signal names Communication conditions Factory settingPin assignments and control Control commandsCable specifications Connecting to a PC Computer Projector DTE specificationsIndication of lamp monitor Dismantle the air filter Cleaning and replacement of air filterProcedure of cleaning Clean the air filterAfter When to replace the Lamp unitReplacing the lamp unit LampHave a Phillips screwdriver ready ahead of time Lamp unit replacement stepsRemove the two screws securing the fan unit Lamp unit will be hot after it has been usedInstallation procedure Ceiling Mount Bracket SafeguardsImage is blurred Power doesNot turn on No imagePT-D4000U SpecificationsReplacement lamp unit Length of power cord CabinetOutside dimensions Remote control Power sourcePAL-M/PAL60 PAL/PAL-N/SECAM Compatible Signal ListInstallation dimensions diagram DimensionsTrademark Acknowledgement Concernant LA Sécurité Ne pas mettre d’objets étrangers dans le projecteur Précautions concernant la sécuritéNe pas surcharger la prise de courant Ne jamais tenter de modifier ou de démonter le projecteurNe jamais démonter la lampe Pendant un orage, ne pas toucher le projecteur ou le câbleNe pas utiliser la lampe usée Ne pas empêcher la chaleur de s’échapperPrécautions pour l’utilisation Nettoyage et maintenancePrécautions pour la manipulation Mise au rebutAprès Remplacement de la lampeMoment adéquat pour remplacer la lampe LampePréparez un tournevis Phillips à l’avance Procédure de remplacement de la lampeLa lampe est chaude si elle vient d’être utilisée Panasonic Canada Inc Panasonic Projector Systems CompanyTechnical Support
Top Page Image Contents