Panasonic PT-D4000U manual How to adjust the lens, How to adjust the FOCUS, Zoom and Shift

Page 24

How to install and remove the projection lens

How to install the projection lens

Align the guide of the projection lens with the guide groove in the main unit. Turn the lens clockwise until it clicks into place.

Guide groove Guide

Guide groove

 

 

 

Guide

 

 

 

 

 

 

 

How to adjust the lens

How to adjust the FOCUS, ZOOM and SHIFT

The focus, zoom and up/down position of the images projected on the screen can be adjusted while the projector is positioned appropriately in relation to the screen.

At the projector

Press LENS on the control panel on the main unit.

Pressing the button changes the setup screen in the order of “FOCUS”, “ZOOM” and “SHIFT”.

Press to select an item and adjust it.

Using the remote control

Press LENS (FOCUS/ZOOM/SHIFT) on the remote control.

Lens signal contact

Projection lens

When the FOCUS button is pressed :

The focus is adjusted.

Attention • Turn the lens counterclockwise and confirm that the lens does not come

off.

How to remove the projection lens

Turn the lens counterclockwise as far as it will go.

While holding down the lens release button, turn the lens further counterclockwise.

Remove the lens.

Lens release button

Note • Before replacing the lens, turn off the projector’s power.

Do not touch the lens signal contact. Dust or dirt may cause defective contact.

Do not touch the surface of the projection lens with your bare hands.

Store the replaced lens where it will be free from vibration and impact.

When the ZOOM button is pressed :

The zoom is adjusted.

When the SHIFT button is pressed :

The shift is adjusted.

Press to select an item and adjust it.

Caution

Be careful not to catch your fingers between the lens and shroud when shifting the lens.

Note

• When a lens without zoom functions

 

is used, the lens zoom adjustment

 

menu will still displayed, but no

 

operations can be performed using

 

the items on this menu.

 

 

• By shifting the lens up/down position,

 

it is possible to make adjustments

 

upward or downward from the

 

standard position in the direction of

 

the upper 50 % of the projected

 

screen height. However, when using

 

ET-DLE050 lens, the shift adjustment

 

is not possible.

 

 

• Operations can be performed faster

 

by holding down the

buttons

 

for about 3 or more seconds.

 

• Do not adjust the lens focus in the

 

initial period (within 30 minutes) after

 

switching on.

 

 

• A warm-up period of at least 30 minutes

 

is recommended before using the

 

projector.

 

24

Image 24
Contents Operating Instructions Commercial UseImportant Safety Notice Dear Panasonic CustomerPage Contents Precautions with regard to safety Remove empty batteries from the remote control at once Do not use or handle the batteries improperlyDo not disassemble the lamp unit Always disconnect all cables before moving the projectorAccessories Do not use the old lamp unitDo not place the projector in extremely hot locations Precautions on handling Remote control Name and function of partsBottom Front and side of the projector Status LED lightsRear view of the main unit Controls on rear panel Side-mounted connection terminals Using the remote control unit Effective range of remote control operationLoading dry cells Setting projector ID number to remote control Connect to the projector to use with a cableInstallation Installation geometryProjection schemes Projection distance by projection lens Screen aspect ratioInstallation Calculation formulas for projection distance by lens types Setup precautions ConnectionExample of connecting with AV products Example of connecting with PCsPowering up the projector Making adjustment and selectionPress the I button. on the main unit or the remote control ProjectionPowering off the projector Direct power off functionHow to adjust the lens How to adjust the FOCUS, Zoom and ShiftHow to remove the projection lens Automatic adjustment Press the Status button on the remote controlStatus function Press the Shutter button againOn-screen menus Structure of menu screensMenu items setting Resetting to the factory defaultBasic menu operations Returning to the previousAdjusting the picture Adjusting the position Clock Phase ZoomKeystone Digital Cinema RealityInput Resolution XGA ModeSxga Mode Clamp PositionOPTION1 settings DVI Signal Level DVI EdidFUNC1 OSD PositionOPTION2 settings InstallationProjector ID AltitudeLamp Select Lamp RelayRS-232C Auto Power OFF PasswordSystem Information Date and TimeSetting the network Connecting the PCSystem requirements Connection exampleUsing Web Browser Control Accessing from the Web browserPassword change Click OKChange password button Basic controlDetail control Error information Monitor informationOK Normal operation Failed Occurrence of trouble Mail set up When Failed has appeared for an item Parameter DescriptionMail set up page Continuing Authentication server set up DNS server set upPing test Contents of mail sent Adjust clockNetwork config Network statusUsing the PJLink protocol Supported commandsPJLink security authentication Command Control Description RemarksSetting the security Password ChangeDisplay Setting Control Device SetupUsing the serial terminals Pin assignments and signal namesCommunication conditions Factory setting Examples of connectionControl commands Cable specificationsConnecting to a PC Computer Projector DTE specifications Pin assignments and controlIndication of lamp monitor Cleaning and replacement of air filter Procedure of cleaningClean the air filter Dismantle the air filterWhen to replace the Lamp unit Replacing the lamp unitLamp AfterLamp unit replacement steps Remove the two screws securing the fan unitLamp unit will be hot after it has been used Have a Phillips screwdriver ready ahead of timeCeiling Mount Bracket Safeguards Installation procedurePower does Not turn onNo image Image is blurredSpecifications PT-D4000ULength of power cord Cabinet Outside dimensionsRemote control Power source Replacement lamp unitCompatible Signal List PAL-M/PAL60 PAL/PAL-N/SECAMDimensions Installation dimensions diagramTrademark Acknowledgement Concernant LA Sécurité Précautions concernant la sécurité Ne pas surcharger la prise de courantNe jamais tenter de modifier ou de démonter le projecteur Ne pas mettre d’objets étrangers dans le projecteurPendant un orage, ne pas toucher le projecteur ou le câble Ne jamais démonter la lampeNe pas empêcher la chaleur de s’échapper Ne pas utiliser la lampe uséeNettoyage et maintenance Précautions pour la manipulationMise au rebut Précautions pour l’utilisationRemplacement de la lampe Moment adéquat pour remplacer la lampeLampe AprèsProcédure de remplacement de la lampe La lampe est chaude si elle vient d’être utiliséePréparez un tournevis Phillips à l’avance Panasonic Projector Systems Company Technical SupportPanasonic Canada Inc