Panasonic PT-D4000U manual Projection, Powering up the projector, Making adjustment and selection

Page 22

Projection
R/PR G/Y B/PB		SYNC/HD VD
VIDEO IN S-VIDEO IN	RGB 1 IN
REMOTE 1	REMOTE 2 IN	IN	SE
IN OUT

Powering up the projector

When using an optional lens, install a projection lens before powering up the projector. (Refer to page 24.)

Remove the lens cover beforehand.

Connect the supplied power cord. (120 V AC, 50 Hz/60 Hz)

Press the “ I ” marked side of the MAIN POWER switch to turn on the power.

The power indicator lights up red, and the projector is placed in the standby mode.

Press the “ I ” button. [on the main unit or the remote control]

The power indicator illuminates in green and soon the image is projected on the screen.

Making adjustment and selection

It is recommended that the projector be allowed to warm up for at least 30 minutes before any adjustments are made to the focus.

<Using the remote control>

Press the FOCUS button to roughly adjust the focus of the lens.*

Set the projection scheme in “INSTALLATION” setting. (page 34)

Select the input signal by pressing the input selector button to toggle through RGB1, RGB2, VIDEO, S-VIDEO and DVI-D.

Turn the feet, and adjust the tilt of the main unit in the front and rear or left and right.

Note • If the projector is powered up at about 0 ˚C, a warm-up period of approximately five

minutes may be necessary to start projection.

The temperature monitor (TEMP) lights during the warm-up period.

When the warm-up is completed, the temperature monitor (TEMP) turns off and the image is projected on the screen.

•If the surrounding temperature is very low and the warm-up period exceeds five minutes, the control determines it as an abnormal condition and turns off the power automatically. If this happens, raise the surrounding temperature to 0 °C or higher and then turn the main power “on” and turn the power “on” ( ).

Use the lens left/right adjustment dial to adjust the direction of the lens. (page 25)

Press the SHIFT button to adjust the “SHIFT”.*

Press the AUTO SETUP button if the input signal is RGB/DVI signal. (page 25)

Press the ZOOM button to fit the image size to the screen size.*

Press the FOCUS button again to adjust the “FOCUS”.*

Press the ZOOM button again to adjust

the “ZOOM” and fit the image size to the screen size.*

*When operating at the projector, please refer to page 24.

22

Image 22

Contents Operating Instructions Commercial UseImportant Safety Notice Dear Panasonic CustomerPage Contents Precautions with regard to safety Do not disassemble the lamp unit Remove empty batteries from the remote control at onceDo not use or handle the batteries improperly Always disconnect all cables before moving the projectorDo not use the old lamp unit AccessoriesDo not place the projector in extremely hot locations Precautions on handling Remote control Name and function of partsBottom Front and side of the projector Status LED lightsRear view of the main unit Controls on rear panel Side-mounted connection terminals Effective range of remote control operation Using the remote control unitLoading dry cells Setting projector ID number to remote control Connect to the projector to use with a cableInstallation geometry InstallationProjection schemes Projection distance by projection lens Screen aspect ratioInstallation Calculation formulas for projection distance by lens types Setup precautions ConnectionExample of connecting with AV products Example of connecting with PCsPress the I button. on the main unit or the remote control Powering up the projectorMaking adjustment and selection ProjectionPowering off the projector Direct power off functionHow to adjust the FOCUS, Zoom and Shift How to adjust the lensHow to remove the projection lens Status function Automatic adjustmentPress the Status button on the remote control Press the Shutter button againOn-screen menus Structure of menu screensBasic menu operations Menu items settingResetting to the factory default Returning to the previousAdjusting the picture Adjusting the position Keystone Clock PhaseZoom Digital Cinema RealitySxga Mode Input ResolutionXGA Mode Clamp PositionOPTION1 settings FUNC1 DVI Signal LevelDVI Edid OSD PositionProjector ID OPTION2 settingsInstallation AltitudeLamp Relay Lamp SelectRS-232C System Information Auto Power OFFPassword Date and TimeSystem requirements Setting the networkConnecting the PC Connection examplePassword change Using Web Browser ControlAccessing from the Web browser Click OKBasic control Change password buttonDetail control Monitor information Error informationOK Normal operation Failed Occurrence of trouble Mail set up When Failed has appeared for an item Parameter DescriptionMail set up page Continuing DNS server set up Authentication server set upPing test Contents of mail sent Adjust clockNetwork config Network statusPJLink security authentication Using the PJLink protocolSupported commands Command Control Description RemarksDisplay Setting Setting the securityPassword Change Control Device SetupCommunication conditions Factory setting Using the serial terminalsPin assignments and signal names Examples of connectionConnecting to a PC Computer Projector DTE specifications Control commandsCable specifications Pin assignments and controlIndication of lamp monitor Clean the air filter Cleaning and replacement of air filterProcedure of cleaning Dismantle the air filterLamp When to replace the Lamp unitReplacing the lamp unit AfterLamp unit will be hot after it has been used Lamp unit replacement stepsRemove the two screws securing the fan unit Have a Phillips screwdriver ready ahead of timeCeiling Mount Bracket Safeguards Installation procedureNo image Power doesNot turn on Image is blurredSpecifications PT-D4000URemote control Power source Length of power cord CabinetOutside dimensions Replacement lamp unitCompatible Signal List PAL-M/PAL60 PAL/PAL-N/SECAMDimensions Installation dimensions diagramTrademark Acknowledgement Concernant LA Sécurité Ne jamais tenter de modifier ou de démonter le projecteur Précautions concernant la sécuritéNe pas surcharger la prise de courant Ne pas mettre d’objets étrangers dans le projecteurPendant un orage, ne pas toucher le projecteur ou le câble Ne jamais démonter la lampeNe pas empêcher la chaleur de s’échapper Ne pas utiliser la lampe uséeMise au rebut Nettoyage et maintenancePrécautions pour la manipulation Précautions pour l’utilisationLampe Remplacement de la lampeMoment adéquat pour remplacer la lampe AprèsLa lampe est chaude si elle vient d’être utilisée Procédure de remplacement de la lampePréparez un tournevis Phillips à l’avance Technical Support Panasonic Projector Systems CompanyPanasonic Canada Inc