Panasonic PT-D4000U manual Accessories, Do not use the old lamp unit

Page 7

If the lamp has broken, ventilate the room immediately. Do not touch or bring your face close to the broken pieces.

•Failure to observe this may cause the user to absorb the gas which was released when the lamp broke and which contains nearly the same amount of mercury as fluorescent lamps, and the broken pieces may cause injury.

•If you believe that you have absorbed the gas or that the gas has got into your eyes or mouth, seek medical advice immediately.

•Ask your dealer about the replacement of the lamp unit and check the inside of the projector.

If not using the projector for an extended period of time, disconnect the power cord plug from the mains socket.

•If dust builds up on the power cord plug, the resulting humidity may damage the insulation, which could result in fire.

Disconnect the power cord plug from the wall outlet as a safety precaution before carrying out any cleaning.

•Electric shocks can result if this is not done.

Be careful not to catch your fingers between the lens and shroud when shifting the lens.

•Do not catch your fingers between the lens and shroud when shifting the lens as it may cause injury.

Ask an Authorized Service Center to clean inside the projector at least once a year.

•If dust is left to build up inside the projector without being cleaned out, it can result in fire or problems with operation.

•It is a good idea to clean the inside of the projector before the season for humid weather arrives. Ask your nearest Authorized Service Center to clean the projector when required. Please discuss with the Authorized Service Center regarding cleaning costs.

If not using the projector for an extended period of time, remove the batteries from the remote control.

•Failure to do so may cause the batteries to leak, overheat, catch fire or explode, possibly resulting in fire or corruption of surrounding areas.

Do not use the old lamp unit.

•The lamp section may break.

Do not place the projector in extremely hot locations.

•Doing so may cause the outer casing or internal components to deteriorate, or result in fire.

•Take particular care in locations exposed to direct sunlight or near stoves.

Accessories

Check that all of the accessories shown below have been included with your projector.

Remote control unit [N2QAYB000164 x 1]

Power cord [K2CG3FZ00008 x 1]

Battery for remote control unit (AA) [R6DW/2ST]

Lens cover [TKKL5244-1 x 1]

Wire cable [TKLA3201 x 1]

Wire fastening M6 screw [XYN6+F10FJ x 1]

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Commercial Use Operating InstructionsDear Panasonic Customer Important Safety NoticePage Contents Precautions with regard to safety Always disconnect all cables before moving the projector Remove empty batteries from the remote control at onceDo not use or handle the batteries improperly Do not disassemble the lamp unitDo not use the old lamp unit AccessoriesDo not place the projector in extremely hot locations Precautions on handling Name and function of parts Remote controlBottom Status LED lights Front and side of the projectorRear view of the main unit Controls on rear panel Side-mounted connection terminals Effective range of remote control operation Using the remote control unitLoading dry cells Connect to the projector to use with a cable Setting projector ID number to remote controlInstallation geometry InstallationProjection schemes Screen aspect ratio Projection distance by projection lensInstallation Calculation formulas for projection distance by lens types Connection Setup precautionsExample of connecting with PCs Example of connecting with AV productsProjection Powering up the projectorMaking adjustment and selection Press the I button. on the main unit or the remote controlDirect power off function Powering off the projectorHow to adjust the FOCUS, Zoom and Shift How to adjust the lensHow to remove the projection lens Press the Shutter button again Automatic adjustmentPress the Status button on the remote control Status functionStructure of menu screens On-screen menusReturning to the previous Menu items settingResetting to the factory default Basic menu operationsAdjusting the picture Adjusting the position Digital Cinema Reality Clock PhaseZoom KeystoneClamp Position Input ResolutionXGA Mode Sxga ModeOPTION1 settings OSD Position DVI Signal LevelDVI Edid FUNC1Altitude OPTION2 settingsInstallation Projector IDLamp Relay Lamp SelectRS-232C Date and Time Auto Power OFFPassword System InformationConnection example Setting the networkConnecting the PC System requirementsClick OK Using Web Browser ControlAccessing from the Web browser Password changeBasic control Change password buttonDetail control Monitor information Error informationOK Normal operation Failed Occurrence of trouble When Failed has appeared for an item Parameter Description Mail set upMail set up page Continuing DNS server set up Authentication server set upPing test Adjust clock Contents of mail sentNetwork status Network configCommand Control Description Remarks Using the PJLink protocolSupported commands PJLink security authenticationControl Device Setup Setting the securityPassword Change Display SettingExamples of connection Using the serial terminalsPin assignments and signal names Communication conditions Factory settingPin assignments and control Control commandsCable specifications Connecting to a PC Computer Projector DTE specificationsIndication of lamp monitor Dismantle the air filter Cleaning and replacement of air filterProcedure of cleaning Clean the air filterAfter When to replace the Lamp unitReplacing the lamp unit LampHave a Phillips screwdriver ready ahead of time Lamp unit replacement stepsRemove the two screws securing the fan unit Lamp unit will be hot after it has been usedInstallation procedure Ceiling Mount Bracket SafeguardsImage is blurred Power doesNot turn on No imagePT-D4000U SpecificationsReplacement lamp unit Length of power cord CabinetOutside dimensions Remote control Power sourcePAL-M/PAL60 PAL/PAL-N/SECAM Compatible Signal ListInstallation dimensions diagram DimensionsTrademark Acknowledgement Concernant LA Sécurité Ne pas mettre d’objets étrangers dans le projecteur Précautions concernant la sécuritéNe pas surcharger la prise de courant Ne jamais tenter de modifier ou de démonter le projecteurNe jamais démonter la lampe Pendant un orage, ne pas toucher le projecteur ou le câbleNe pas utiliser la lampe usée Ne pas empêcher la chaleur de s’échapperPrécautions pour l’utilisation Nettoyage et maintenancePrécautions pour la manipulation Mise au rebutAprès Remplacement de la lampeMoment adéquat pour remplacer la lampe LampeLa lampe est chaude si elle vient d’être utilisée Procédure de remplacement de la lampePréparez un tournevis Phillips à l’avance Technical Support Panasonic Projector Systems CompanyPanasonic Canada Inc
Top Page Image Contents