Panasonic PT-D4000U manual Mail set up, When Failed has appeared for an item Parameter Description

Page 41

When [FAILED] has appeared for an item

Parameter

Description

 

 

MAIN CPU BUS

Trouble has occurred in the microcomputer circuitry. Consult your dealer.

FAN

Trouble has occurred in the fan or its drive circuit. Consult your dealer.

OPTICS MODULE

The temperature inside the projector is high.

It may be that the projector is being used where the ambient temperature is

TEMPERATURE

high such as near a heating appliance.

 

INPUT AIR TEMPERATURE

The input air temperature is too high.

It may be that the projector is being used where the ambient temperature is

 

high such as near a heating appliance.

AROUND LAMP

The temperature near the lamp has risen very high.

TEMPERATURE

Something may be blocking the exhaust vent.

LAMP REMAIN TIME

The lamp runtime has exceeded the prescribed cumulative time, and it is

now time to replace the lamp.

 

LAMP STATUS

The lamp has failed to light.

Wait a short while for the lamp to cool off, and then turn on the power.

 

SHUTTER

Trouble has occurred in the shutter circuitry. Consult your dealer.

AIR FILTER

Too much dust accumulates on the air filter.

Turn off the MAIN POWER switch using the procedure on page 23 and

 

clean the air filter (refer to page 51).

OPTICS MODULE TEMP.SENSOR

Trouble has occurred in the temperature detection sensor inside the

projector. Consult your dealer.

 

INPUT AIR TEMP.SENSOR

Trouble has occurred in the sensor used to detect the input air temperature.

Consult your dealer.

 

AROUND LAMP

Trouble has occurred in the temperature detection sensor around lamps.

TEMP. SENSOR

Consult your dealer.

BATTERY

The backup battery has been run out. Consult your dealer.

AIRFLOW SENSOR

Trouble has occurred in the air volume sensor. Consult your dealer.

COLOR WHEEL

Trouble has occurred in the color wheel or the color wheel drive circuit.

Consult your dealer.

 

COVER OPEN

The lamp unit cover is not properly fitted. Check the fitting of the lamp unit

cover. (page 53)

 

E-mail set up page

With this projector, if a problem occurs or if the lamp usage time reaches a set value, an E-mail message can be sent to one or more preset E-mail addresses (maximum two addresses). Click [Projector control], then [E-mail set up] to display the E-mail set up page.

The user can modify the threshold temperature for sending temperature warning mail. If the temperature rises above the set value, control sends temperature warning mail.

Select “Enable” to use the E-mail function.

Enter the IP address or server name of the E-mail server (SMTP). The DNS server must be set if the server name is entered.

Enter the E-mail address of the projector. (maximum 63 characters)

The user can enter the location of, for example, the installed projector so that the recipient may easily identify the originator of the E-mail.

(maximum 63 characters)

The user can modify the minimum time interval of temperature warning mail. The default value is 60 minutes. In this case, the user cannot send another mail for 60 minutes after sending previous temperature warning mail even the set warning temperature is reached again.

(Continued on the next page)

41

Image 41
Contents Commercial Use Operating InstructionsDear Panasonic Customer Important Safety NoticePage Contents Precautions with regard to safety Do not use or handle the batteries improperly Remove empty batteries from the remote control at onceDo not disassemble the lamp unit Always disconnect all cables before moving the projectorDo not place the projector in extremely hot locations AccessoriesDo not use the old lamp unit Precautions on handling Name and function of parts Remote controlBottom Status LED lights Front and side of the projectorRear view of the main unit Controls on rear panel Side-mounted connection terminals Loading dry cells Using the remote control unitEffective range of remote control operation Connect to the projector to use with a cable Setting projector ID number to remote controlProjection schemes InstallationInstallation geometry Screen aspect ratio Projection distance by projection lensInstallation Calculation formulas for projection distance by lens types Connection Setup precautionsExample of connecting with PCs Example of connecting with AV productsMaking adjustment and selection Powering up the projectorPress the I button. on the main unit or the remote control ProjectionDirect power off function Powering off the projectorHow to remove the projection lens How to adjust the lensHow to adjust the FOCUS, Zoom and Shift Press the Status button on the remote control Automatic adjustmentStatus function Press the Shutter button againStructure of menu screens On-screen menusResetting to the factory default Menu items settingBasic menu operations Returning to the previousAdjusting the picture Adjusting the position Zoom Clock PhaseKeystone Digital Cinema RealityXGA Mode Input ResolutionSxga Mode Clamp PositionOPTION1 settings DVI Edid DVI Signal LevelFUNC1 OSD PositionInstallation OPTION2 settingsProjector ID AltitudeRS-232C Lamp SelectLamp Relay Password Auto Power OFFSystem Information Date and TimeConnecting the PC Setting the networkSystem requirements Connection exampleAccessing from the Web browser Using Web Browser ControlPassword change Click OKDetail control Change password buttonBasic control OK Normal operation Failed Occurrence of trouble Error informationMonitor information When Failed has appeared for an item Parameter Description Mail set upMail set up page Continuing Ping test Authentication server set upDNS server set up Adjust clock Contents of mail sentNetwork status Network configSupported commands Using the PJLink protocolPJLink security authentication Command Control Description RemarksPassword Change Setting the securityDisplay Setting Control Device SetupPin assignments and signal names Using the serial terminalsCommunication conditions Factory setting Examples of connectionCable specifications Control commandsConnecting to a PC Computer Projector DTE specifications Pin assignments and controlIndication of lamp monitor Procedure of cleaning Cleaning and replacement of air filterClean the air filter Dismantle the air filterReplacing the lamp unit When to replace the Lamp unitLamp AfterRemove the two screws securing the fan unit Lamp unit replacement stepsLamp unit will be hot after it has been used Have a Phillips screwdriver ready ahead of timeInstallation procedure Ceiling Mount Bracket SafeguardsNot turn on Power doesNo image Image is blurredPT-D4000U SpecificationsOutside dimensions Length of power cord CabinetRemote control Power source Replacement lamp unitPAL-M/PAL60 PAL/PAL-N/SECAM Compatible Signal ListInstallation dimensions diagram DimensionsTrademark Acknowledgement Concernant LA Sécurité Ne pas surcharger la prise de courant Précautions concernant la sécuritéNe jamais tenter de modifier ou de démonter le projecteur Ne pas mettre d’objets étrangers dans le projecteurNe jamais démonter la lampe Pendant un orage, ne pas toucher le projecteur ou le câbleNe pas utiliser la lampe usée Ne pas empêcher la chaleur de s’échapperPrécautions pour la manipulation Nettoyage et maintenanceMise au rebut Précautions pour l’utilisationMoment adéquat pour remplacer la lampe Remplacement de la lampeLampe AprèsPréparez un tournevis Phillips à l’avance Procédure de remplacement de la lampeLa lampe est chaude si elle vient d’être utilisée Panasonic Canada Inc Panasonic Projector Systems CompanyTechnical Support