Panasonic PT-D4000U manual Precautions with regard to safety

Page 5

Precautions with regard to safety

WARNING

If you notice smoke, strange smells or noise coming from the projector, disconnect the power cord plug from the wall outlet.

Do not continue to use the projector in such cases, otherwise fire or electric shocks could result.

Check that no more smoke is coming out, and then contact an Authorized Service Center for repairs.

Do not attempt to repair the projector yourself, as this can be dangerous.

Installation work (such as ceiling suspension) should only be carried out by a qualified technician.

If installation is not carried out correctly, there is the danger that injury or electric shocks may occur.

Use the dedicated ceiling mount bracket specified for the model.

Use the provided safety wire cable and take measures to prevent the projector from falling.

Do not overload the wall outlet.

If the power supply is overloaded (for example, by using too many adapters), overheating may occur and fire may result.

Do not look into the lens while the projector is being used.

Strong light is emitted from the projector’s lens. If you look directly into this light, it can hurt and damage your eyes.

Be especially careful not to let young children look into the lens. In addition, turn off the power and disconnect the power cord plug when you are away from the projector.

Never attempt to modify or disassemble the projector.

High voltages can cause fire or electric shocks.

For any inspection, adjustment and repair work, please contact an Authorized Service Center.

Do not install this projector in a place which is not strong enough to take the full weight of the projector or on top of a surface which is unstable.

If the projector is installed in a place which is not strong enough or on top of a surface which is sloped or unstable, it may fall down or tip over, and severe injury or damage could result.

If foreign objects or water get inside the projector, or if the projector is dropped or the cabinet is broken, disconnect the power cord plug from the wall outlet.

Continued use of the projector in this condition may result in fire or electric shocks.

Contact an Authorized Service Center for repairs.

Do not place liquid containers on top of the projector.

Do not place the projector into water or let it become wet.

If water spills onto the projector or gets inside it, fire or electric shocks could result.

If any water gets inside the projector, contact an Authorized Service Center.

Do not insert any foreign objects into the projector.

Do not insert any metal objects or flammable objects into the projector or drop them onto the projector, as doing so can result in fire or electric shocks.

Use only the power cord supplied with the projector.

Do not use the supplied power cord with equipment other than the projector.

Failure to observe this may result in electric shocks.

Insert the power cord plug securely into the wall outlet.

If the plug is not inserted correctly, electric shocks or overheating could result.

Do not use plugs which are damaged or wall outlets which are coming loose from the wall.

Do not do anything that might damage the power cord or the power cord plug.

Do not damage the power cord, make any modifications to it, place it near any hot objects, bend it excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle.

If the power cord is used while damaged, electric shocks, short-circuits or fire may result.

Ask an Authorized Service Center to carry out any repairs to the power cord that might be necessary.

Clean the power cord plug regularly to prevent it from becoming covered in dust.

If dust builds up on the power cord plug, the resulting humidity can damage the insulation, which could result in fire. Pull the power cord plug out from the wall outlet and wipe it with a dry cloth.

If not using the projector for an extended period of time, pull the power cord plug out from the wall outlet.

Do not handle the power cord plug with wet hands.

Failure to observe this may result in electric shocks.

5

Image 5
Contents Commercial Use Operating InstructionsDear Panasonic Customer Important Safety NoticePage Contents Precautions with regard to safety Do not use or handle the batteries improperly Remove empty batteries from the remote control at onceDo not disassemble the lamp unit Always disconnect all cables before moving the projectorDo not place the projector in extremely hot locations AccessoriesDo not use the old lamp unit Precautions on handling Name and function of parts Remote controlBottom Status LED lights Front and side of the projectorRear view of the main unit Controls on rear panel Side-mounted connection terminals Loading dry cells Using the remote control unitEffective range of remote control operation Connect to the projector to use with a cable Setting projector ID number to remote controlProjection schemes InstallationInstallation geometry Screen aspect ratio Projection distance by projection lensInstallation Calculation formulas for projection distance by lens types Connection Setup precautionsExample of connecting with PCs Example of connecting with AV productsMaking adjustment and selection Powering up the projectorPress the I button. on the main unit or the remote control ProjectionDirect power off function Powering off the projectorHow to remove the projection lens How to adjust the lensHow to adjust the FOCUS, Zoom and Shift Press the Status button on the remote control Automatic adjustmentStatus function Press the Shutter button againStructure of menu screens On-screen menusResetting to the factory default Menu items settingBasic menu operations Returning to the previousAdjusting the picture Adjusting the position Zoom Clock PhaseKeystone Digital Cinema RealityXGA Mode Input ResolutionSxga Mode Clamp PositionOPTION1 settings DVI Edid DVI Signal LevelFUNC1 OSD PositionInstallation OPTION2 settingsProjector ID AltitudeRS-232C Lamp SelectLamp Relay Password Auto Power OFFSystem Information Date and TimeConnecting the PC Setting the networkSystem requirements Connection exampleAccessing from the Web browser Using Web Browser ControlPassword change Click OKDetail control Change password buttonBasic control OK Normal operation Failed Occurrence of trouble Error informationMonitor information When Failed has appeared for an item Parameter Description Mail set upMail set up page Continuing Ping test Authentication server set upDNS server set up Adjust clock Contents of mail sentNetwork status Network configSupported commands Using the PJLink protocolPJLink security authentication Command Control Description RemarksPassword Change Setting the securityDisplay Setting Control Device SetupPin assignments and signal names Using the serial terminalsCommunication conditions Factory setting Examples of connectionCable specifications Control commandsConnecting to a PC Computer Projector DTE specifications Pin assignments and controlIndication of lamp monitor Procedure of cleaning Cleaning and replacement of air filterClean the air filter Dismantle the air filterReplacing the lamp unit When to replace the Lamp unitLamp AfterRemove the two screws securing the fan unit Lamp unit replacement stepsLamp unit will be hot after it has been used Have a Phillips screwdriver ready ahead of timeInstallation procedure Ceiling Mount Bracket SafeguardsNot turn on Power doesNo image Image is blurredPT-D4000U SpecificationsOutside dimensions Length of power cord CabinetRemote control Power source Replacement lamp unitPAL-M/PAL60 PAL/PAL-N/SECAM Compatible Signal ListInstallation dimensions diagram DimensionsTrademark Acknowledgement Concernant LA Sécurité Ne pas surcharger la prise de courant Précautions concernant la sécuritéNe jamais tenter de modifier ou de démonter le projecteur Ne pas mettre d’objets étrangers dans le projecteurNe jamais démonter la lampe Pendant un orage, ne pas toucher le projecteur ou le câbleNe pas utiliser la lampe usée Ne pas empêcher la chaleur de s’échapperPrécautions pour la manipulation Nettoyage et maintenanceMise au rebut Précautions pour l’utilisationMoment adéquat pour remplacer la lampe Remplacement de la lampeLampe AprèsPréparez un tournevis Phillips à l’avance Procédure de remplacement de la lampeLa lampe est chaude si elle vient d’être utilisée Panasonic Canada Inc Panasonic Projector Systems CompanyTechnical Support