Panasonic PTAE8000U Switchingthe projectorthe projectoron/off on/off Power cord, Power indicator

Page 28

Switchingthe projectorthe projectoron/off on/off

Power cord

Use the power cord included to prevent removal of the power cord and make sure it is fully inserted into the projector.

Make sure the <MAIN POWER> switch is on the <OFF> side before connecting the power cord. Use the power cord included and ensure that it is fully inserted.

For power cord handling details, see “Read this first!”. (pages 6 to 13)

■■Connecting

■■Disconnecting

Fully insert until the tabs on the left and right make a click sound.

Pull out while pushing on the tabs on the sides.

Basic Operation

Power indicator

The power indicator indicates the power status. Check the status of the power indicator <ON (G) / STANDBY (R)>

before operating the projector.Power indicator

Indicator status

 

 

 

 

Status

 

 

 

 

 

 

No illumination or flashing

Main power is switched off.

 

 

 

 

 

 

 

 

 

Power is switched off. (Standby mode.)

 

Lit

Press the power <

 

/ > button to start projection.

 

 

 

 

Red

 

* Does not operate when the lamp indicator or temperature indicator is flashing.

 

 

 

 

 

 

 

Power is switched off (standby mode) and the [POWER ON LINK] is set to

 

 

 

Flashing

[YES] in the VIERA Link settings.

 

 

For details about [POWER ON LINK], see [POWER ON LINK] (page 82).

 

Flashing

The projector is preparing to project.

Green

Projection starts after a brief pause.

 

 

Lit

Projecting.

 

 

 

 

 

 

 

 

Lit

Preparing to switch off the power.

 

The power is switched off after a while. (Changes to the standby mode.)

 

 

Orange

 

 

 

 

 

 

 

The power <

 

/ > button is switched on again in the power off preparation

 

 

 

 

 

Flashing

mode.

 

 

Preparing to project. Projection starts after a brief pause.

 

 

 

 

 

 

 

Attention

zzThe internal fan operates and cools the projector while it is preparing to power off (when the power indicator is illuminated orange). Do not switch the main power off or remove the power cord.

Note

zzWhen the power < / > button is pressed while the projector is in the power off preparation mode, it may take some time to enter projection mode.

zzThe projector consumes approx. 0.08 W of electrical power even when the power is off (when the power indicator is illuminated red).

zzPower consumption when the power indicator flashes red is almost the same as when the lamp is illuminated red.

28 - ENGLISH

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Operating Instructions Trademarks Illustrations in these operating instructions ReferencesTerm These instructions, references to pages are indicated as Features of the Projector Quick StepsContents Maintenance ContentsAppendix Power Readthisthisfir t! firstSupply ResultRead this first FCC Notice USANotification Canada Declaration of ConformityDo not use anything other than the provided power cord Electric shocks can resultFailure to observe this will result in electric shocks Do not overload the wall outletDo not cover the air intake port or the air exhaust port Never attempt to remodel or disassemble the projectorDo not project an image with the lens cover attached Doing so can cause fireLamp replacement Do not allow infants or pets to touch the remote controlDo not disassemble the lamp unit If the lamp breaks, it could cause injuryDo not put your weight on this projector Do not place heavy objects on top of the projectorDo not place the projector in extremely hot locations Always disconnect all cables before moving the projectorThis may lead to a worsening of medical conditions Watching for long periods of time may cause eye fatigueDo not move about while wearing the 3D Eyewear This could lead to injury or eye fatiguePressione a guia e levante a tampa BrasilRemova as baterias Precautionsf usefor use Projector is designed for indoor use onlyPrecautions for use ZzDo not install the projector in an enclosed spaceAbout disposal Order to view clear video imagesOptional accessories Precautions for use AccessoriesOptional accessories Model No Product names Aboutyouryourprojectorprojector Remote control Remote control signal transmitterSend remote control signal TopTop and front view About your projector Projector bodyControl panel About your projector Connecting terminalsBack and bottom view Setting up Setting upProjection method Parts for ceiling mount optionalHeight position Setting up Projection relatedLW LT Front adjustable feet and throwing angle Projection screen sizeAdjusting the lens shift Setting up Lens shift and positioningRemove the lens shift cover Projector Projector location rangeShift direction Connecting example Component IN/S-VIDEO IN/VIDEO Connections Before connecting to the projectorDVD player Video player Connections Connecting example Hdmi IN/COMPUTER 3D IR Transmitter optional accessory connectionBlu-ray player Computer IR cable Included with 3D IR TransmitterPower indicator Switchingthe projectorthe projectoron/off on/off Power cordIndicator status Status Switching the projector on/off Switching on the projector Press the power / buttonZzThe power indicator illuminates or flashes red Remove the lens coverIndicator to turn red or start flashing red Switching the projector on/off Switching off the powerZzThe confirmation message is displayed Selecting the input signal Adjusting the imageProjecting an image Projecting an imageManaging the lens control settings Selecting the picture modeAdjusting the picture Remotecontrolcontrolope ationoperationLoading a saved setting Remote control operationResetting to the default settings Displaying the Viera Link menuRemote control operation Submenu Switching the input signalUsing the Function button Displaying the 3D Settings menuViewing 3D Images About viewing 3D imagesViewing 3D Images Viewing 3D imagesScreen Approx m ScreenOperating procedure Returning adjusted values to default settingsMenu navigation Navigating through the menuSubmenu items Default Setting Menu navigation Menu listPicture Position3D Settings LanguageLens Control OptionPicture Mode ContrastBrightness ColorColor Temperature SharpnessPicture menu Dynamic IrisAdjust the waveform Auto AdjustMonitor Position Adjust Full Scany / Single Line Adjust Full Scanr / Single LineAdjust Full Scang / Single Line Adjust Full Scanb / Single LineSplit Adjust Use the buttons to select the area to be adjustedPress the Return button Submenu itemsGamma Adjustment You can perform more detailed image adjustment manuallyAdvanced Menu Enter button35 ・・・+0.75 +0.80 00 G 0.00 B ZzThe Advanced Adjust menu appearsInformation of the currently selected point Is displayed Input PointOutput Reference points gray Move above+30 Point Input Output Initialize the gamma adjustment results Select item with the buttons, Adjust with the buttonsAdvanced Menu menu items Default Setting Select OK with the buttons and press the ENTERbuttonContrast BrightnessMpeg NR Frame CreationColor Management Create a new profilePress the Enter button Press the Return button or Menu button twiceEditing/deleting logs Press the buttons to select LOG and press the Enter buttonZzMenu B and the base color C is displayed ZzThe LOG menu is displayedProfile setting will be set to Change You can readjust the colorDelete Deletes color adjustment Press to select the point you wishSaving a log setting as a profile Deleting a profileSelect OK with the buttons Press the Enter button ZzThe Profile Save confirmation message is displayedColor Detail ClarityChanging a profile name Loading saved profilesTV-SYSTEM Cinema RealitySuper White When using Computer input When using an Hdmi 1/2/3 inputPicture Memory RGB/YCBCR, RGB/YPBPRSignal Mode Memory LoadMemory Delete Memory Name ChangeClock Phase POSITIONmenu menuDOT Clock PositionPosition menu AspectHdmi Aspect Screen Input signal Projects at Projection screen Input signalEnlarged horizontally Projection screen Input signal Projects atAuto Setup WSSOver Scan Keystone3DSETTINGSmenu menu Screen Size3D Input Format Side by Side3D Settings menu Switching 3D Format3D effect is not achieved if the power supply is cut off Normal 3D videoAdjustment method LEFT/RIGHT Swap3D Picture Balance Use the buttons to change ValuePicture Balance Memory 3D Waveform MonitorButton Picture Balance Memory Load 3D Settings menu 2D to 3D Press the buttons to select MemoryName Change and press the Enter OFF MODE5 MODE1 MODE43D Eyewear Brightness 3D IR Transmitter3D Viewing Monitor Press the buttons to select Optimum parallax3D Safety Precautions Switch settings Active3D Motion Remaster Blue gauge Red gauge Triangular PointLens Control menu Lens Control menu ZOOM/FOCUSLens Memory Load Press the Return button or Menu ButtonLens Control menu Lens Memory SaveLens Memory Edit Lens Memory DeleteAuto Switching Wide signals are 2.351, 2.401, 2.501, 2.551 aspect signalsLens Memory Name Change Press the buttons to select the memory name to be changedArea Position Left Masking AreaRight Masking Area Upper Masking AreaOption menu ON-SCREEN DisplayOption menu Back ColorHdmi Signal Level Startup LogoAuto Search Frame ResponseOutput Trigger 1/2 SettingInput Power ON/OFF Blank High Altitude ModeSleep Lamp Power Viera Link SettingsHow to cancel function assignment Function ButtonPower on Link Power OFF LinkEnergy Saving Mode Unused Device Energy SaveTest Pattern Other FunctionsLamp Runtime Initialize ALL ZzThe Initialize ALL confirmation message appearsManaging the indicated problems Temp and Lamp IndicatorsTEMP and Lamp IndicatorsTemperature indicator Temp Lamp indicator Lamp Temp and Lamp IndicatorsProblem Cleaning the projector Care and replacementCare and replacement Attach the air filter unit to the projector Care and replacement Component replacement Air filter and electrostatic filterLamp unit Before replacing the lamp unitWhen to replace the lamp unit Over 3 800 *1Hours Over 4 000 *1Remove the video cable connected to the connecting terminal Lamp unit replacement procedureSlowly remove the lamp cover from the projector Assemble the air filter unit Attaching the top cover Select OK with the buttons and then press the Enter buttonTroubleshooting Torque 1.25 ± 0.2 N·m UsingVIERAVIERALink Link Summary of Viera Link featuresUsing an amplifier Viera Link Hdmi connection onlyUsing Viera Link ZzSet up the projectorViera Link Hdavi Control Viera Link Control of compatible equipmentUsing Viera Link Menu of the accessed device appearsIf you access a device other than a Viera Link device Use the menu of the deviceSelect Home Theater Volume with Buttons Press the buttons to adjust the volume of the deviceZzThe volume adjustment bar appears ZzPress the Enter button again to cancel the muteTechnicalinformatiinformation List of compatible signals Signal ModeMode Format of 3D video signals Technical information Supported 3D video signal listFrame Packing Side by Side TOP and Bottom Pin assignments and signal names Communication settingsTechnical information Serial terminal ConnectionCable specifications Control commandsWhen connected to a personal computer Technical informationKST Keystone Inquiry commands ParameterSpecifications Trigger / 3D Shutter OUTDimensions Unit mm345 19/32 60 2 3/8 140 470Index IndexNumbers Panasonic Canada Inc Panasonic System Communications Company of North AmericaOne Panasonic Way 2F-13, Secaucus, NJ TEL 877 803
Related manuals
Manual 8 pages 49.13 Kb

PT-AE8000U, PTAE8000U specifications

Panasonic, a renowned name in the world of electronics, has produced a diverse range of televisions, among which the TC-32LC54, TC-L42U5X, TC-L32C5X, TC-L32C5, and PTAE8000U stand out for their impressive features and innovative technologies.

The Panasonic TC-32LC54 is a 32-inch flat-screen LCD television that delivers a captivating viewing experience. It boasts a resolution of 1366 x 768 pixels, allowing for sharp and vibrant images. The TV features a high contrast ratio and wide viewing angles, thanks to its IPS panel technology. Additionally, the TC-32LC54 includes an integrated digital tuner for seamless access to HD programming.

Next in line is the TC-L42U5X, a 42-inch LCD television that takes the viewing experience to the next level with its Full HD 1080p resolution. This model comes equipped with VIERA's 24p cinematic playback, ensuring that movies are presented as intended by filmmakers. The TC-L42U5X is also energy-efficient, featuring an Eco Mode that reduces power consumption while maintaining optimum picture quality. Users can enjoy enhanced connectivity with multiple HDMI inputs and USB ports.

The TC-L32C5X offers a perfect blend of performance and affordability. This 32-inch model features LED backlighting for improved contrast and brightness. The TC-L32C5X supports multiple media formats through its USB port, allowing users to enjoy photos, music, and videos directly from USB drives. Furthermore, the TV's VIERA Link feature simplifies the connection of multiple devices, making it easy to control everything with a single remote.

In contrast, the TC-L32C5 is designed for those seeking reliable performance without excessive features. This 32-inch LCD model offers solid picture quality and viewing angles, making it suitable for smaller living spaces. It includes essential connectivity options like HDMI and RCA input, ensuring compatibility with a range of devices.

Finally, the PTAE8000U is a high-performance projector that brings cinematic experiences to the home theater. With a resolution of 1080p and a brightness of 2400 lumens, it delivers stunning visuals even in well-lit rooms. The PTAE8000U features advanced lens shift capabilities, allowing for easy installation in various settings. Its THX certification ensures accurate color reproduction and exceptional sound quality, enhancing the overall viewing experience.

In conclusion, Panasonic's lineup of TVs and projectors demonstrates the brand's commitment to quality, performance, and innovation, catering to various consumer needs and preferences.
Top Page Image Contents