Panasonic PT-AE8000U, PTAE8000U manual Care and replacement, Cleaning the projector

Page 87

Care and replacement

Before cleaning the projector / replacing components

Attention

zzTurn off the <MAIN POWER> switch and disconnect the power plug from the wall outlet before cleaning the projector/replacing components.

zzFollow the “Switching off the power” procedure when turning off the projector. (page 30)

Cleaning the projector

■■Cleaning the outer surface of the projector

Wipe off dirt and dust gently with a soft dry cloth.

zzIf it is difficult to remove the dirt, soak a cloth in water, wring the cloth well and then wipe the projector. Dry the projector with a dry cloth.

zzDo not use petroleum benzene, thinner, any alcoholic solvent, or kitchen detergents. Using these substances may result in changes or damage to the surface of the projector.

zzWhen using a chemically treated cloth, follow the accompanying guidelines.

■■Cleaning the lens surface

If dirt or dust accumulates on the surface of the lens, it will be enlarged and projected onto the screen.

Wipe dirt and dust from the front of the lens gently with a clean, soft, and dry cloth.

zzDo not use a fluffy rag, or a greasy, wet, or dirty cloth.

zzDo not rub the lens harshly as this may damage the surface.

Attention

zzThe lens is made of glass. It may break or crack if struck with a hard object or rubbed harshly. Please be careful when handling the lamp.

Care and replacement

■■Air filter unit

If too much dust accumulates in the air filter the internal temperature of the projector cannot be maintained at the normal level. A confirmation message is displayed on the screen, and at the same time <TEMP> illuminates red. The power is cut off automatically after a while. Clean the filter after every 100 hours of usage.

1)Remove the air filter cover.

zzUsing a Phillips screwdriver to turn the fixing screw of the air filter cover until loose and remove the cover.

Air filter cover fixing screw

Air filter cover

2)Remove the air filter unit.

zzHold the grips on the air filter unit, and remove it from the projector.

Air filter unit

UP

Grips ( arrow engraved)

*After removing the air filter unit, remove any large build ups of dirt or dust in the air filter unit bay and the air intake port on the projector.

3)Vacuum dirt and dust from the air filter

unit.

zzDo not wash the air filter unit.

Maintenance

ENGLISH - 87

Page 86 Page 88
Image 87
Page 86 Page 88
Contents Operating Instructions These instructions, references to pages are indicated as  TrademarksIllustrations in these operating instructions References TermQuick Steps Features of the ProjectorContents Contents MaintenanceAppendix Result PowerReadthisthisfir t! first SupplyDeclaration of Conformity Read this firstFCC Notice USA Notification CanadaDo not overload the wall outlet Do not use anything other than the provided power cordElectric shocks can result Failure to observe this will result in electric shocksDoing so can cause fire Do not cover the air intake port or the air exhaust portNever attempt to remodel or disassemble the projector Do not project an image with the lens cover attachedIf the lamp breaks, it could cause injury Lamp replacementDo not allow infants or pets to touch the remote control Do not disassemble the lamp unitAlways disconnect all cables before moving the projector Do not put your weight on this projectorDo not place heavy objects on top of the projector Do not place the projector in extremely hot locationsThis could lead to injury or eye fatigue This may lead to a worsening of medical conditionsWatching for long periods of time may cause eye fatigue Do not move about while wearing the 3D EyewearBrasil Pressione a guia e levante a tampaRemova as baterias Projector is designed for indoor use only Precautionsf usefor useZzDo not install the projector in an enclosed space Precautions for useOrder to view clear video images About disposalPrecautions for use Accessories Optional accessoriesOptional accessories Model No Product names Top Aboutyouryourprojectorprojector Remote controlRemote control signal transmitter Send remote control signalAbout your projector Projector body Top and front viewControl panel Connecting terminals About your projectorBack and bottom view Parts for ceiling mount optional Setting upSetting up Projection methodSetting up Projection related Height positionLW LT Projection screen size Front adjustable feet and throwing angleSetting up Lens shift and positioning Adjusting the lens shiftRemove the lens shift cover Projector location range ProjectorShift direction Connections Before connecting to the projector Connecting example Component IN/S-VIDEO IN/VIDEODVD player Video player IR cable Included with 3D IR Transmitter Connections Connecting example Hdmi IN/COMPUTER3D IR Transmitter optional accessory connection Blu-ray player ComputerSwitchingthe projectorthe projectoron/off on/off Power cord Power indicatorIndicator status Status Remove the lens cover Switching the projector on/off Switching on the projectorPress the power / button ZzThe power indicator illuminates or flashes redSwitching the projector on/off Switching off the power Indicator to turn red or start flashing redZzThe confirmation message is displayed Projecting an image Selecting the input signalAdjusting the image Projecting an imageRemotecontrolcontrolope ationoperation Managing the lens control settingsSelecting the picture mode Adjusting the pictureDisplaying the Viera Link menu Loading a saved settingRemote control operation Resetting to the default settingsDisplaying the 3D Settings menu Remote control operation SubmenuSwitching the input signal Using the Function buttonViewing 3D images Viewing 3D ImagesAbout viewing 3D images Viewing 3D ImagesScreen Screen Approx mNavigating through the menu Operating procedureReturning adjusted values to default settings Menu navigationPosition Submenu items Default SettingMenu navigation Menu list PictureOption 3D SettingsLanguage Lens ControlColor Picture ModeContrast BrightnessDynamic Iris Color TemperatureSharpness Picture menuAuto Adjust Adjust the waveformMonitor Position Adjust Full Scanb / Single Line Adjust Full Scany / Single LineAdjust Full Scanr / Single Line Adjust Full Scang / Single LineSubmenu items Split AdjustUse the buttons to select the area to be adjusted Press the Return buttonEnter button Gamma AdjustmentYou can perform more detailed image adjustment manually Advanced MenuZzThe Advanced Adjust menu appears 35 ・・・+0.75 +0.80 00 G 0.00 BInformation of the currently selected point Is displayed Point InputOutput Move above Reference points gray+30 Point Input Output Select OK with the buttons and press the ENTERbutton Initialize the gamma adjustment resultsSelect item with the buttons, Adjust with the buttons Advanced Menu menu items Default SettingFrame Creation ContrastBrightness Mpeg NRPress the Return button or Menu button twice Color ManagementCreate a new profile Press the Enter buttonZzThe LOG menu is displayed Editing/deleting logsPress the buttons to select LOG and press the Enter button ZzMenu B and the base color C is displayedPress to select the point you wish Profile setting will be set toChange You can readjust the color Delete Deletes color adjustmentZzThe Profile Save confirmation message is displayed Saving a log setting as a profileDeleting a profile Select OK with the buttons Press the Enter buttonLoading saved profiles ColorDetail Clarity Changing a profile nameCinema Reality TV-SYSTEMSuper White RGB/YCBCR, RGB/YPBPR When using Computer inputWhen using an Hdmi 1/2/3 input Picture MemoryMemory Name Change Signal ModeMemory Load Memory DeletePosition Clock PhasePOSITIONmenu menu DOT ClockAspect Position menuHdmi Projects at Aspect Screen Input signalProjects at Projection screen Input signal Enlarged horizontally Projection screen Input signalKeystone Auto SetupWSS Over ScanSide by Side 3DSETTINGSmenu menuScreen Size 3D Input FormatNormal 3D video 3D Settings menuSwitching 3D Format 3D effect is not achieved if the power supply is cut offUse the buttons to change Value Adjustment methodLEFT/RIGHT Swap 3D Picture Balance3D Waveform Monitor Picture Balance MemoryButton Picture Balance Memory Load OFF MODE5 MODE1 MODE4 3D Settings menu 2D to 3DPress the buttons to select Memory Name Change and press the Enter3D IR Transmitter 3D Eyewear BrightnessPress the buttons to select Optimum parallax 3D Viewing MonitorBlue gauge Red gauge Triangular Point 3D Safety PrecautionsSwitch settings Active 3D Motion RemasterPress the Return button or Menu Button Lens Control menu Lens Control menuZOOM/FOCUS Lens Memory LoadLens Memory Delete Lens Control menuLens Memory Save Lens Memory EditPress the buttons to select the memory name to be changed Auto SwitchingWide signals are 2.351, 2.401, 2.501, 2.551 aspect signals Lens Memory Name ChangeUpper Masking Area Area PositionLeft Masking Area Right Masking AreaBack Color Option menuON-SCREEN Display Option menuFrame Response Hdmi Signal LevelStartup Logo Auto SearchTrigger 1/2 Setting OutputInput High Altitude Mode Power ON/OFF BlankSleep Function Button Lamp PowerViera Link Settings How to cancel function assignmentUnused Device Energy Save Power on LinkPower OFF Link Energy Saving ModeOther Functions Test PatternLamp Runtime ZzThe Initialize ALL confirmation message appears Initialize ALLTemp and Lamp IndicatorsTEMP and Lamp Indicators Managing the indicated problemsTemperature indicator Temp Temp and Lamp Indicators Lamp indicator LampProblem Care and replacement Cleaning the projectorCare and replacement Attach the air filter unit to the projector Before replacing the lamp unit Care and replacement Component replacementAir filter and electrostatic filter Lamp unitOver 4 000 *1 When to replace the lamp unitOver 3 800 *1 HoursLamp unit replacement procedure Remove the video cable connected to the connecting terminalSlowly remove the lamp cover from the projector Assemble the air filter unit Select OK with the buttons and then press the Enter button Attaching the top coverTroubleshooting Torque 1.25 ± 0.2 N·m Viera Link Hdmi connection only UsingVIERAVIERALink LinkSummary of Viera Link features Using an amplifierViera Link Control of compatible equipment Using Viera LinkZzSet up the projector Viera Link Hdavi ControlUse the menu of the device Using Viera LinkMenu of the accessed device appears If you access a device other than a Viera Link deviceZzPress the Enter button again to cancel the mute Select Home Theater Volume with ButtonsPress the buttons to adjust the volume of the device ZzThe volume adjustment bar appearsSignal Mode Technicalinformatiinformation List of compatible signalsTechnical information Supported 3D video signal list Mode Format of 3D video signalsFrame Packing Side by Side TOP and Bottom Connection Pin assignments and signal namesCommunication settings Technical information Serial terminalTechnical information Cable specificationsControl commands When connected to a personal computerKST Keystone Parameter Inquiry commandsSpecifications Shutter OUT Trigger / 3D140 470 DimensionsUnit mm 345 19/32 60 2 3/8Index IndexNumbers Panasonic System Communications Company of North America Panasonic Canada IncOne Panasonic Way 2F-13, Secaucus, NJ TEL 877 803
Related manuals
Manual 8 pages 49.13 Kb

PT-AE8000U, PTAE8000U specifications

Panasonic, a renowned name in the world of electronics, has produced a diverse range of televisions, among which the TC-32LC54, TC-L42U5X, TC-L32C5X, TC-L32C5, and PTAE8000U stand out for their impressive features and innovative technologies.

The Panasonic TC-32LC54 is a 32-inch flat-screen LCD television that delivers a captivating viewing experience. It boasts a resolution of 1366 x 768 pixels, allowing for sharp and vibrant images. The TV features a high contrast ratio and wide viewing angles, thanks to its IPS panel technology. Additionally, the TC-32LC54 includes an integrated digital tuner for seamless access to HD programming.

Next in line is the TC-L42U5X, a 42-inch LCD television that takes the viewing experience to the next level with its Full HD 1080p resolution. This model comes equipped with VIERA's 24p cinematic playback, ensuring that movies are presented as intended by filmmakers. The TC-L42U5X is also energy-efficient, featuring an Eco Mode that reduces power consumption while maintaining optimum picture quality. Users can enjoy enhanced connectivity with multiple HDMI inputs and USB ports.

The TC-L32C5X offers a perfect blend of performance and affordability. This 32-inch model features LED backlighting for improved contrast and brightness. The TC-L32C5X supports multiple media formats through its USB port, allowing users to enjoy photos, music, and videos directly from USB drives. Furthermore, the TV's VIERA Link feature simplifies the connection of multiple devices, making it easy to control everything with a single remote.

In contrast, the TC-L32C5 is designed for those seeking reliable performance without excessive features. This 32-inch LCD model offers solid picture quality and viewing angles, making it suitable for smaller living spaces. It includes essential connectivity options like HDMI and RCA input, ensuring compatibility with a range of devices.

Finally, the PTAE8000U is a high-performance projector that brings cinematic experiences to the home theater. With a resolution of 1080p and a brightness of 2400 lumens, it delivers stunning visuals even in well-lit rooms. The PTAE8000U features advanced lens shift capabilities, allowing for easy installation in various settings. Its THX certification ensures accurate color reproduction and exceptional sound quality, enhancing the overall viewing experience.

In conclusion, Panasonic's lineup of TVs and projectors demonstrates the brand's commitment to quality, performance, and innovation, catering to various consumer needs and preferences.
Top Page Image Contents