Loading a saved setting
Displays the [MEMORY LOAD] menu.
Press
Attention
zzSetting can also be performed using the
Displaying the [VIERA LINK] menu
You can control some functions of the external device with this projector remote control.
Press
Note
zzSee “Using VIERA Link” for details. ( page 96)
Displaying the waveform monitor
By displaying the output signal from a connected external device with a waveform, you can check if the video signal (luminance) level is set to a value within this projector’s recommended range, and can adjust it accordingly.
Press
The settings change as follows each time the <ENTER> button is pressed.
[FULL SCAN (Y)] |
|
|
|
|
| [FULL SCAN (R)] | ||
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
[SINGLE LINE SCAN (B)] |
|
|
|
|
| [FULL SCAN (G)] | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
[SINGLE LINE SCAN (G)] |
|
|
|
|
| [FULL SCAN (B)] | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
[SINGLE LINE SCAN (R)] |
|
|
|
|
| [SINGLE LINE SCAN (Y)] | ||
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
The waveform monitor disappears when the <WAVEFORM MONITOR> button is pressed again.
Note
zzSetting can also be performed using the
Remote control operation
[FULL | Checks that the waveform for each of the | |
Y‑ (brightness), R‑ (red), G‑ (green), and | ||
SCAN] | B‑ (blue) values for the whole image is | |
| within the recommended range. | |
| Checks that the waveform for each of the | |
| Y‑ (brightness), R‑ (red), G‑ (green), and | |
| B‑ (blue) values for an arbitrary number | |
| of lines from the top of the screen to the | |
[SINGLE | bottom is within the recommended range. | |
LINE | zzEnables more detailed confirmation than | |
SCAN] | [FULL SCAN]. | |
zzLine position can be changed with the ▲▼ | ||
| ||
| buttons. | |
| zzThe display position of the [WAVEFORM | |
| MONITOR] changes depending on the line | |
| position. |
Note
zzSignals lower than 0 % in the waveform monitor will be displayed as same as 0 % on the projected image. zz[SINGLE LINE SCAN] can display horizontal lines in Y‑
(brightness), R‑ (red), G‑ (green), and B‑ (blue) from the top of the screen to the bottom more finely than [FULL SCAN], and each item can be adjusted in the same way as [FULL SCAN].
zzWhen selecting [FULL SCAN], the display position of the waveform can be set using the ▲▼▲▼ buttons.
zzSo that the display of individual adjustment screen in [PICTURE] does not interfere with the waveform monitor, the positioning of this screen differs depending on the circumstances at the time.
zzThe [AUTO ADJUST] is executed by pressing the <DEFAULT> button while the waveform is displayed. ( page 42)
zzWhile the waveform monitor is displayed, you cannot adjust the [COLOR MANAGEMENT] settings.
zzWhen a 3D signal is being input (including converting 2D to 3D), the waveform monitor cannot be displayed.
zzIf a 3D signal is input while the waveform monitor is being displayed, the waveform monitor disappears.
Resetting to the default settings
You can reset most of the settings or adjustment values for submenus to factory default settings.
Press
For details, see “Navigating through the menu - Returning adjusted values to default settings” of “Menu navigation”. ( page 37)
Basic Operation