TechniSat DIGITY CI Operating Manual manual Timer, Programming via EPG

Page 21

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 21

6.12 Timer

Your receiver is equipped with a timer. This allows you to make video recordings even when you are away. The timer mode is indicated by a blinking control LED in the display. Timer mode can be cancelled by pressing the On/Standby key.

6.12.1 Programming via EPG:

>Switch to the programme on which the item to be recorded is broadcast.

>Press the EPG key. The EPG table of the programme selected will be displayed.

>Use the arrow keys up/down to mark the required programme.

>Press the yellow function key (Record).

The data relating to the marked programme will now be stored in the timer memory, and will be displayed on screen for control purposes. (Fig. 6-11)

>To delete a marked timer, press the green function key (Delete) and confirm when asked to do so on screen.

>Press the Back key to return to the EPG table, and, if you wish, to programme additional timer events

or

>Press the TV/Radio key to return to normal

operation.

The receiver will now select the appropriate programme at the programmed time, and will, if instructed to do so, revert to stand-by mode at the end of the programme.

6.12.2Manual programming/Changing timer set- tings

In addition to EPG timer programming you can also carry out manual programming of the timer. To do this, proceed as follows:

>Press the Menu key to display the Main Menu.

>Mark the item Timer and confirm by pressing OK. The Timer menu will be displayed. (Fig. 6-12)

>Press the yellow function key (New) to go to timer programming, in order to programme a new timer event. (Fig. 6-13)

>To alter an existing timer setting, mark this by using the arrow keys up/down. Press the yellow function key (Change) to access the settings of the marked

timer.

For programming, proceed as follows:

Source

>Use the arrow keys to mark the item Source, then use the OK key to enter the required source (TV or

Radio).

(Fig. 6-11)

(Fig. 6-12)

(Fig. 6-13)

21

Image 21

Contents Digity CI Contents BedanlDIGITY CIQuark3en.qxd 31.01.03 1647 Seite Illustrations Remote controlRear panel Front panelImportant operating information Please read this firstSafety Note When not in operationEnvironmental note VCR Connections Mains power connectionExternal unit Connection to a television setBasic settings InstallationHi-fi amplifier Serial interface RSParental control Audio/Video settingsTime difference GMT hours CountryLanguage Audio signal LNB setting/Adjusting to external unit/Satellite selectionScart mode Image format TV setSwitching DiSEqC on and off Setting the switching matrix and the LNB characteristicsMenu LNB Settings Additional Settings Switching on and off OperationProgramme selection Using the programme list Selecting a listCalling up blocked programmes Volume control Reception of encrypted programmesInformation box Selecting a different language Multifeed optionsTime control Near Video On Demand Return to previous programme Switching between TV and RadioDisplay clock and programme information Additional programme informationElectronic Programme Guide Transponder InformationTimer Manual programming/Changing timer set- tingsProgramming via EPG VCR Using the internal video text decoder Using the video text decoder of your television setVideo text PreselectChanging basic programming Calling up the programme listAdding programmes to the programme list Deleting from the Favourites list Deleting programmesDeleting from the Total list Use the arrow keys left/right to select Yes or NoBlocking access to programmes parental control Sorting programmesKeys up/down or the numeric keys Unblocking access control for individual programmes SettingsChanging the PIN Satellite Programme SearchTransponder Integrating programmes after a search Manual searchRestoring basic programming/ Delete all Activating default settingDelete all programmes Updating softwareUse the arrow keys left/right to indicate Yes or Abort Encryption system System configurationOperation in conjunction with a rotary Antenna Eastern and Western limitsSetting Western limit Setting Eastern limitUse the arrow keys left/right to mark the item LNB test Use the arrow keys up/down to mark the item Delete limitsPress the arrow key left Geo-positioningSetting user-defined satellite positions User Satellite Setting the satellite positionAdjusting the satellite antenna Test-Transponder/LNB-configurationAntenna manual adjustment Automatic fine adjustment Autofocus Saving satellite positionsList of current satellites Deleting a satellite position Reference positionSelecting a satellite position DVB Technical TermsLOF Scart FEC Technical dataTV-SCART Dear customer Trouble-shooting guideProblem Possible cause Solution City Geogr. Longitude E Geogr. Latitude N Annexure Co-ordinates of selected German citiesCo-ordinates of selected German cities City Geogr. LongitudeE Geogr. Latitude N For everyday use TV/radio switching